R INSTALLATION GUIDE TM Britt Single Handle Commercial Kitchen Faucet KPF-1690 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Place bucket under angle stops.
Diagram and Parts List B A H E F D G1 C1 C2 C3 G2 A. Spray Head E. Escutcheon B. Faucet Body F. Base Plate C. Mounting Hardware G. Escutcheon Mounting Hardware C1. Rubber & Metal Washer G1. Bolt C2. Mounting Nut G2. Plastic Nut C3. Mounting Screw H. 2.5 mm Hex Wrench D.
Faucet Dimensions 10 3/4" (271.6mm) 4 5/8" 8 1/2" (116.6mm) 6 1/2" 2 1/8" (163.8mm) (525.5mm) 20 3/4" (215mm) 2 1/8" (54.2mm) (55.
Step 1. Remove mounting hardware Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove mounting hardware (C) from faucet body (B). C Step 2. Install the faucet assembly (without deckplate) Before installation, ensure that the flange (D) is placed on the bottom of the new faucet assembly (B). Insert the faucet body through the hole in the sink. NOTE: Skip this step and move on to Step 3 if installing with deckplate.
Step 3. Install the escutcheon E G1 F Before installation, remove the flange (D). Screw the bolts (G1) into the escutcheon (E) and ensure that the base plate (F) is pressed onto the escutcheon (E) before the escutcheon (E) is installed over the three holes on the sink. From underneath the sink, hand tighten the mounting nuts (G2). Do not overtighten. NOTE: Skip this step if installing without deckplate. G2 Step 4.
Step 5. Secure the faucet assembly Install the plastic washer and metal washer (C1) onto the threaded mounting shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3). Do not overtighten. C1 C2 C3 Step 6. Connect the waterlines Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with wrench. Do not overtighten.
Step 7. Flush and check for leaks Pull hose assembly out of spout and remove spray head by unscrewing from hose in a counterclockwise direction. Hold the end of the hose down into the sink and turn the faucet on to the warm position. Flush water lines for one minute to flush away any debris. Check for leaks. Re-tighten any connections if needed. Do not overtighten. Reinstall spray head by hand tightening it back onto the spray hose.
Care & Maintenance To keep the product clean & shining, follow the steps below: 1. 2. 3. 4. Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives or harsh cleaners Do not use cloth with a coarse surface Unscrew the aerator and clean when necessary ACID Download the Kraus Care & Maintenance Guide at: http://www.kraususa.com/maintenance This installation manual is subject to change without further notice.
Replacement Parts Replacement Parts List 1. Spray Head 06 07 05 11 08 Finish/Color Part # SFS,MB* KP27022 2. Check Valve KP27023 3. Washer KP27031 4. S.S. Hose 5. Inverter 6. Spring 7. Washer KP27080 8. O-ring KP27029 9. Block KP27030 SFS,MB* KP27026 SFS,BG,SB* 11. Spray Support Assembly 12. Set Screw 10 12 14 04 15 03 02 13 17 01 16 20 18 19 SFS,BGMB, MBSB* 13. Flow Regulator KP27034 14. Cartridge KP27035 15. Bonnet Nut KP27036 16. Cap 17. Handle 19.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle The bonnet nut (15) has come loose and the ring on the cartridge is dirty or damaged Tighten the bonnet nut. Clean or replace the cartridge Leaking between spray head and the hose Spray head (1) may be loose or washer (3) is not seated correctly in the hose connection.
Codes/Standards Applicable: FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
