R INSTALLATION GUIDE TM Britt Single Handle Commercial Kitchen Faucet KPF-1690 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Place bucket under angle stops.
Diagram and Parts List B I A H E F D G1 C1 C2 C3 G2 A. Spray Head E. Escutcheon B. Faucet Body F. Base Plate C. Mounting Hardware G. Escutcheon Mounting Hardware C1. Rubber & Metal Washer G1. Bolt C2. Mounting Nut G2. Plastic Nut C3. Mounting Screw D. Flange & Washer H. 2.5 mm Hex Wrench I. 2.
Faucet Dimensions 10 3/4" (271.6mm) (162mm) 8 1/2" (46mm) (76mm) MAX 3" (215mm) 1 3/4" (7.9mm) 1/4" 6 3/8" (524mm) 20 5/8" 4 5/8" (116.6mm) 3/8" Compression Ø1 3/8" (34mm) R1 1/4" (30.3mm) 2 3/8" (60.6mm) 10" (255.6mm) 1/4" (7.
Step 1. Remove mounting hardware Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove mounting hardware (C) from faucet body (B). C Step 2. Install the faucet assembly (without deckplate) Before installation, ensure that the flange (D) is placed on the bottom of the new faucet assembly (B). Insert the faucet body through the hole in the sink. NOTE: Skip this step and move on to Step 3 if installing with deckplate.
Step 3. Install the escutcheon E G1 F Before installation, remove the flange (D). Screw the bolts (G1) into the escutcheon (E) and ensure that the base plate (F) is pressed onto the escutcheon (E) before the escutcheon (E) is installed over the three holes on the sink. From underneath the sink, hand tighten the mounting nuts (G2). Do not overtighten. NOTE: Skip this step if installing without deckplate. G2 Step 4.
Step 5. Secure the faucet assembly Install the plastic washer and metal washer (C1) onto the threaded mounting shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3). Do not overtighten. C1 C2 C3 Step 6. Connect the waterlines Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with wrench. Do not overtighten.
Step 7. Flush and check for leaks Pull hose assembly out of spout and remove spray head by unscrewing from hose in a counterclockwise direction. Hold the end of the hose down into the sink and turn the faucet on to the warm position. Flush water lines for one minute to flush away any debris. Check for leaks. Re-tighten any connections if needed. Do not overtighten. Reinstall spray head by hand tightening it back onto the spray hose.
Replacement Parts Replacement Parts List 1. Spray Head 06 3. 1.8 GPM Washer KP27196 BLAB,BLBG,BLSFSB BLMB,BLSFACB,SFS* KP27025 5. Inverter GR,BL* KP27026 6. Spring SFS,BG,SFACB,SFSB,AB* KP27027 7. Inverter GR,BL* KP27080 KP27030 9. Block 10. Washer 11. Spray Support Assembly 12. Set Screw 09 10 12 GR,BL* KP27031 SFS,AB,BG,SFSBMB SFACBMB,BGMB* KP27032 KP27033 13. Cartridge 13 02 16 01 KP27035 14. Bonnet Nut 14 For 2.2 GPM option 03 KP27029 8.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle The bonnet nut (14) has come loose and the ring on the cartridge is dirty or damaged Tighten the bonnet nut. Clean or replace the cartridge Leaking between spray head and the hose Spray head (1) may be loose or washer (3) is not seated correctly in the hose connection.
Care & Maintenance To keep the product clean & shining, follow the steps below: 1. 2. 3. 4. Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives or harsh cleaners Do not use cloth with a coarse surface Unscrew the aerator and clean when necessary ACID Download the Kraus Care & Maintenance Guide at: http://www.kraususa.com/maintenance This installation manual is subject to change without further notice.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R ASME A112.18.1 1.8GPM 6.8L/min maximum C C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
INSTALLATION GUIDE Purita™ Single Handle Water Filtration Faucet FF-100 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List A G B C D E F A. Faucet Assembly B. Flange C. Rubber Washer D. Metal Washer E. Mounting Nut F. Connector G.
Faucet Dimension 7 1/8” 2 3/4“ [181.5mm] [69.5mm] 6” 8 3/8“ [212.0mm] 12” [304.5mm] [153.0mm] Ø1 3/4" [Ø45.0mm] [77.
Step 1: Preparing for installation Remove the rubber washer (C), metal washer (D), and mounting nut (E) from the end of the stud. C D E Step 2: Installing the faucet assembly A C D E 5 Place the faucet assembly (A) through the selected hole in the sink or countertop. On the underside of the sink or countertop, slide the rubber washer (C) and metal washer (D) onto the stud. Thread the mounting nut (E) onto the stud, and tighten securely using your wrench.
Step 3: Connecting the quick connect adaptor and water line A Thread the quick connect adaptor (F) onto the end of the faucet assembly (A) stud, and tighten securely using a wrench. Connect the 3/8 in. water line from the filtration system by pushing the line into the connector (F). Pull down on the 3/8 in. line slightly to ensure the quick connect fitting has engaged. F 3/8 in.
Replacement Parts 1 Replacement Parts List Finish / Color 1 2 3 4 5 CH, SFS, MB, BG, KP27169 BB, SFACB, SFSB* 3. Locking Ring KP27170 4. O-ring KP27171 5. Cartridge KP27172 6. Handle CH, SFS, MB, BG, KP27173 BB, SFACB, SFSB* 7. Index GR, BL* 8. Flange CH, SFS, MB, BG, KP27174 BB, SFACB, SFSB* KP27194 9. Rubber Washer KP27175 10. Metal Washer KP27176 11. Mounting Nut KP27177 12. Connector KP27178 13.
10 Trouble - Shooting 9 Hexagon Nut 11 If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: 12 PROBLEM C A U S13E ACTION Leakage under the handle Cartridge (5) has come loose Remove index (7) and loosen set screw with hex wrench (13). Remove the Cold handle.
Codes/Standards Applicable: NSF/ANSI 372 LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1 1GPM 3.8L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (”Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered foe the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
