R INSTALLATION MANUAL Merlin Single Handle Pull-Down Kitchen Faucet TM KPF-1674 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Flush angle stops to release any debris prior to installation.
Diagram and Parts List 1. Spray Head 1 6 2 9 3A 3B 2. Faucet Body 3. Hot and Cold Waterlines A. Hot B. Cold 4. Quick Connector 5. Mounting Hardware A. Rubber Washer B. Metal Washer C. Mounting Nut D. Mounting Screws 6. Spray hose 7. Weight 8. Hex Wrench 9.
Faucet Installation Procedure 4 (1 9 1/8" (231.5mm) 3 3/4" 1 1/8" (94.6mm) (30mm) 6 7/8" (175mm) 15 5/8" (396.4mm) 12° " /8 m) 5 79.8m 8 5/8" (218.5mm) 11 1/4" (284.7mm) MAX. 1 3/8" (35mm) Ø1 3/8" (35mm) Installer Tip: Shut off main water supply before installing new faucet.
Step 1A. Faucet installation - with deck plate For three-hole installation: Deck plate, base plate and silicone sealant (optional) are required. Note: Optional deck plate not included. 3A 3B Step 1B. Faucet installation - without deck plate For single-hole installation: Deck plate, base plate and silicone sealant are NOT required.
Step 2. Install faucet and mounting hardware Insert faucet body (2) into hole in countertop or deck plate assembly. Install mounting hardware (5A, B, C & D) from underneath the countertop. 5A 5B 5C 5D Step 3. Secure mounting hardware Adjust direction of faucet body (2) so that handle is on right side of faucet. Tighten mounting nut (5C) until snug. Tighten mounting screws (5D) to nut with a Phillips screwdriver until snug.
Step 4. Attach spray hose and counterweight Connect spray hose (7) to quick connector (4) attached to supply line. Install weight (8) on lowest vertical point on spray hose (7). 4 7 8 Step 5. Connect waterlines Connect waterlines (3) to angle stops. Tighten both ends of waterlines with a wrench until snug. Turn on hot and cold angle stops and check for leaks. 3 NOTE: Make sure filter washers are installed.
Step 6. Flush spray hose 7 Remove spray head (1) from spray hose (7). Hold tip of spray hose (7). Turn faucet on and let the water run for 60 seconds to flush any debris. 1 Step 7. Check for leaks Check for leaks at the connections. Retighten if necessary.
Replacement Parts 5 6 4 7 8 Replacement Parts List Finish/Color Part # 1. Spray Head SFS,MB,BG* KP06089 2. Check Valve KP06107 3. Washer KP06074 4. Spray Hose SFS,MB,BG* KP06097 5. Hose Guide KP06007 6. Plastic Clip KP06168 7. Handle Button 8. Set Screw 9. Metal Handle SFS,MB,BG* KP06029 3 2 9 12 11 10 13 22 14 4 23 15 16 17 10. Cartridge Cover KP06054 SFS,MB,BG* KP06169 SFS,MB,BG* KP06171 11. Locking Nut KP06170 12. Cartridge KP06103 13. Base O-Ring KP06172 14.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated. Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand. Tighten locking nut with an adjustable wrench.
Maintenance - Cartridge Replacement Step 1: Remove button located at the top of the handle. Loosen the set screw with a hex wrench. Remove the handle and unscrew cartridge cover by hand. Step 2: Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge. Step 3: Place the new cartridge in the handle seat. Secure the cartridge with the locking nut and assemble the handle.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
