R INSTALLATION MANUAL Nolen Single Handle Pull-Down Kitchen Faucet TM KPF-1673 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2022 Kraus USA Plumbing LLC I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List 10 6 1 9 2 11 5 8B 8A 7 3A 1. Spray Head 2. Faucet Body 3. Deck Plate Assembly A. Deck Plate B. Base Plate 4. Mounting Hardware A. Rubber & Metal Washer B. Mounting Nut C. Mounting Screws 5. Spray Hose 6. Weight 7. Quick Connector 8. Hot and Cold Copper Lines A. Cold B. Hot 9. Hex Wrench 10. Washer 11.
Faucet Installation Procedure (99mm) 7" (178mm) 9" (228mm) (417mm) 3 7/8" (291mm) 16 3/8" 11 1/2" 9 1/8" 1/2" MAX 2 1/4" (12mm) (232mm) (57mm) 2X G1/2" Ø1 3/8" (35mm) 2 3/4" (70mm) 10 3/8" (264mm) 1/2" (12mm) * Optional Deck Plate Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware Remove the mounting screws (4C), mounting nut (4B), and rubber & metal washer (4A) from the mounting pipe. 4A 4B 4C Step 2A. Faucet installation - with deck plate For three-hole installation: Deck plate (3A), base plate (3B), and silicone sealant (optional) are required.
Step 2B. Faucet installation - without deck plate For single-hole installation: Deck plate (3A), base plate (3B), and silicone sealant are NOT required. Step 3. Install faucet and mounting hardware Insert faucet body (2) into hole in countertop or deck plate assembly (3). Install mounting hardware (4A, B & C) from underneath the countertop.
Step 4. Secure mounting hardware 4B 4C Adjust direction of faucet body (2) so that handle is on right side of faucet. Tighten mounting nut (4B) until snug. Tighten mounting screws (4C) to nut with Phillips screwdriver until snug. Step 5. Attach spray hose and counterweight Connect spray hose (5) to quick connector (7) attached to supply line. Install weight (6) on lowest vertical point on spray hose (5).
Step 6. Connect waterlines 8 12 Connect waterlines to hot and cold copper lines (8). Connect waterlines (12) to angle stops. Tighten both ends of waterlines with a wrench until snug. Turn on hot and cold angle stops and check for leaks. NOTE: Check the filter washer in the waterlines before connecting to the angle stops. Step 7. Flush spray hose 5 1 Remove spray head (1) from spray hose (5). Hold tip of spray hose (5). Turn faucet on and let the water run for 60 seconds to ush any debris.
Replacement Parts Replacement Parts List 1. Spray Head 25 4 29 3 2 26 1 11 8 22 23 24 13 12 10 9 7 14 15 17 18 19 20 16 21 *Denotes faucet component color options: SFS - Spot Free Stainless Steel CH - Chrome BL - Black GR - Grey 6 SFS, CH* KP06091 KP06105 SFS, CH* KP06098 4. Hose Guide KP06045 5. Spout Clip KP06292 6. Metal Handle SFS, CH* KP06000 7. Handle Button BL, GR* KP06026 KP06052 8. Set Screw 9. Cartridge Cover 5 Part # 2. Check Valve 3.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated. Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand. Tighten locking nut with an adjustable wrench. Water does not shut off Cartridge may need to be adjusted or replaced.
Maintenance - Cartridge Replacement Step 1: Remove button located at the top of the cartridge cover. Loosen the set screw with a hex wrench. Remove the handle and unscrew cartridge cover by hand. Step 2: Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge. Step 3: Place the new cartridge in the handle seat. Secure the cartridge with the locking nut and assemble the handle.
Codes/Standards Applicable: NSF/ANSI 372 UP NSF/ANSI/CAN 61: Q ≤ 1 UP C C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R Faucet Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
