INSTALLATION MANUAL Artec Pro™ 2 Function Commercial Style Kitchen Faucet KPF-1603 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I Rev.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List A. B1. B2. B3. B4. B5. C.
Faucet Dimensions 4 1/8" 7 1/8" (106.5mm) 24 3/4" (628.7mm) (182.6mm) 6" (60.8mm) (60mm) MAX. 2 3/8" 2 3/8" 6 5/8" 7 5/8" (198.2mm) (173.3mm) (153.2mm) 9 3/4" (248.2mm) 3/8" Compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Remove washer and lock nut Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove the mounting hardware (B) from the faucet body (A). A B Step 2. Installing the faucet Insert the faucet through the hole in the sink or countertop. From underneath the sink, attach the seat (B1), rubber washer (B2), metal washer (B3), and nut (B4). Lock nut (B4) into position by tightening screws (B5).
Step 3. Making the water supply connections Push the quick connector (2) firmly upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made. If it is necessary to remove the quick connector (2), squeeze the tabs on the hose and then pull down to disconnect. 1 2 Step 4. Making the water supply connections 1 Thread the nut (1) on the supply line onto the outlet of the water supply valve and tighten with a wrench. Do not overtighten.
Step 5. Flushing and checking for leaks Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks. Reinstall the spray head by hand tightening it back onto the spray hose.
Step 6. Flush faucet To activate the spray mode, simply press the handle (1) located under the spray head.
Replacement Parts Replacement Parts List 1. Spray Head 2. Magnet 4 5 3. Spray Hose Assembly 4. Spring 6 3 5. Inverter 6. Spray Support 2 Assembly 7 1 7. Spout Nut 8 9 10 18 19 20 8. Spout 9. Diverter 1112 13 15 16 17 10.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the handle. Bonnet nut (12) has come loose. Remove the index (14.3). Loosen set screw (14.2) with hex wrench (14). Remove the handle (14.1). Unscrew cap (13) (by hand only). Tighten bonnet nut (12) with an adjustable wrench The aerator has an irregular or reduced water flow. The aerator is dirty or misfitted.
Codes/Standards Applicable: NSF/ANSI 372 UP NSF/ANSI/CAN 61: Q ≤ 1 UP C C R C LEAD FREE IA PM C OR R NSF/ANSI 61 &T TM ASME A112.18.1 1.8GPM 6.8L/min maximum Faucet - Lifetime Limited Warranty Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com R If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
