R INSTALLATION MANUAL Ripiano Series Top Mount Kitchen Sinks TM KGTW1-33 / KGTW2-33 / KGTW12-33 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2020 Kraus USA Plumbing LLC I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure that you have all necessary parts by checking the parts list.
Tools you will need Safety Goggles Drill Silicone Adhesive Jig Saw Hammer Phillips Screwdriver Tape Measure Pencil Masking Tape Hole Saw NOTE: Specialized tools may be necessary to install Kraus Granite Kitchen sinks with countertop materials other than wood, marble or granite.
Hardware (Included) A B Kit for Drop-In Installation Important · Instructions may vary depending on countertop material. Read all instructions carefully, and ensure that counters are compatible with sink installation before proceeding. · Follow the plumber’s code and builder’s code effective in your area. · Shut off water valves prior to installation. · Open sink packaging and verify that the sink is in perfect condition. Put sink back into packaging to protect it until time of installation.
33" (838.1mm) 1 1/2" (38.2mm) (207.1mm) 8 1/8" (245mm) 9 5/8" (727mm) (227.7mm) 28 5/8" 5/8" (15mm) 28 5/8" (727mm) Model #: KGTW1-33 Sink Dimensions: 33” x 22” x 9 5/8” Min Cabinet Size: 36” Model #: KGTW2-33 Sink Dimensions: 33” x 22” x 9 5/8” Min Cabinet Size: 36” 5 1/4" (6mm) (133.4mm) 16" (406.4mm) R1/4" 5 1/4" 3 3/4" (380.9mm) (93.7mm) 17" (431.8mm) 22" (558.7mm) 15 1/8" (35mm) (133.4mm) Ø1 3/8" 3" 1 7/8" 3 1/2" (89mm) (46.3mm) 3 1/2" (89mm) (76.2mm) 30" (761.
1. Trace Opening · Locate the drop-in template in the box. · Cut carefully along the dotted lines. Keep the inside portion of the template. It contains important information concerning care and maintenance for your new sink. · Place the template on the counter, in the location where you will be installing the sink. When placing the template, note the location of cabinet doors and panels to ensure that they are compatible with sink installation.
2. Cut Opening · Using the drill, make a small starting hole of about 1/2” on the inside of the cutting line. · Drill a second time in the same hole with a larger bit to enlarge the hole so that the jigsaw can be inserted properly. · Put masking tape on the outer side of the cutting line. This will protect the counter from scratches and shattered fragments caused by the jigsaw. · Using the jigsaw, trim the inside of the cutting line. · Insert the sink and adjust the opening if necessary.
3. Add Additional Faucet Hole (Optional) · Determine the location of the faucet. · Place the sink upside down on a suitable flat surface. · Using the 35mm (1 3/8”) diamond hole saw at high power (1500tr. per break through in the desired location. CAUTION: This procedure will cause the metal saw to become very hot. Please handle with care. 4.
5. Install Sink · Clean and dry the surface around the opening of the sink. · Verify that the sink fits correctly in the opening. The edge of the sink must sit on the counter. · Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included) underneath the edge of the sink. · Ensure that the plastic flap holding the screw underneath the sink is partially opened, as shown. · Insert the sink into the opening.
5.
6. Install Drain · Insert the metal strainer into the rubber seal, and then into the drain hole. · Insert the rubber gasket and the main drain body underneath the sink. · Using the screw, tighten the main drain body and the metal strainer into place. · Insert the basket on top of the drain installation. BASKET SCREW METAL STRAINER RUBBER SEAL RUBBER GASKET MAIN BODY 7. Install Pipes · Install the faucet following the manufacturer's instructions. · Make proper water and waste pipe connections.
Maintenance Clean your sink on a regular basis with warm soapy water. Rinse the sink after using cleaning products. Wipe the sink surface with a soft cloth to remove any liquid residue. Do not cut food directly on the surface of the Do not leave sharp objects on the surface of the sink for an extended period of time. Do not use abrasive cleaning products, sanding tools, steel wool or bleaching products. Download the Kraus Care & Maintenance Guide at: http://www.kraususa.
Codes/Standards Applicable UP C C R Kitchen Sink Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Plumbing LLC ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Kitchen Sink" in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
Installation Instructions Kraus Kitchen Sink Strainer ST-4 1 Pull knob & basket assembly Step 1: Remove the pull knob and basket assembly 2 Main connecting screw Step 2: Disassemble the outlet by removing the main connecting screw (screw will be reinstalled in Step 5) 3 Stainless steel outlet top Step 3: Separate the parts and place the stainless steel outlet top and center it in the 90mm sink hole from above Note: Seal between underside of strainer body flange and inside of sink with plumber’s putty
