All-In-One Kitchen Set KCA-1200 ©
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Make sure to check off that you have all of the following items Kitchen Sink - KBU32 Kitchen Faucet - KPF-1610SS Cut-Out Template Undermounting Hardware Bottom Grid - KBG-32 (2) Drains - ST-1 (2) Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement.
Tools you will need: Safety Goggles Drill Silicone Adhesive Jig Saw Scissors Phillips Screwdriver Tape Measure Pencil Screwdriver Putty Knife NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Undermount sinks with countertop materials other than wood, marble or granite.
14 1/2" 368mm 368mm 19" 483mm 17" 14 1/2" 432mm Dimensions: 32" 216mm 8 1/2" 813mm Model #: KBU32 Sink Dimensions: 32” x 19” x 8 1/2” Min Cabinet Size: 36” Matching Grid: KBG-32 (2) Drain Model #: ST-1 (2) 5
1. Determine Reveal Type Use scissors to cut along the line of the paper template for your desired reveal type (Negative, Positive or Flushed Reveal).
2. Position Template · · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. 3. Trace Template · Trace template on countertop with a pencil.
4. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
5. Set up Mounting Brackets · · Turn countertop over and align sink with countertop. Decide location for mounting brackets. Mounting holes should be 1/2" from edge of sink. 6. Drill Hole in Countertop · Drill 3/8" diameter x 1/2" deep hole in countertop.
7. Install Anchors · Insert anchors into drilled holes and lightly tap with a hammer until flush. 8. Secure Sink to Countertop · Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly.
9. Attach Mounting Hardware · · Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
10. Install Plumbing Fixtures · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Maintenance Clean your sink on a regular basis with warm soapy water. Rinse the sink after using cleaning products. Wipe the sink surface with a soft cloth to remove any liquid residue. Do not cut food directly on the surface of the sink.
Diagram and Parts List 1. Spray Head 2. Faucet Body 3. Mounting Hardware A. Rubber Washer B. Metal Washer C. Mounting Nut D. Mounting Screws 4. Supply Hose 5. Hot & Cold Waterlines 6. Hose 7. Washer 8. Weight 9. Hex Wrench 10. Washer (2.2GPM) Please note: This faucet is designed with a 1.8 gpm flow rate in compliance with CEC standards. To adjust the flow rate to 2.2 gpm, replace the washer (7) with the 2.2 gpm washer provided in package.
Faucet Installation Procedure 10 3/4" 274mm 4 1/2" 115mm 8 3/4" 221mm 18" 456mm 6 3/8" 162mm 2 1/8" 54mm Installer Tip Shut off main water supply before installing new faucet 14
1. Remove mounting hardware · Remove the mounting screws (3D), mounting nut (3C), metal (3B) and rubber washer (3A) from the mounting pipe. 2. Install faucet mounting hardware · Insert faucet body (2) into hole in countertop. Install mounting hardware (3A, B, C & D) from underneath the countertop.
3. Secure mounting hardware · Adjust direction of faucet body (2) so that the handle is on the right side of the faucet. Tighten mounting nut (3C) until snug. Tighten mounting screws (3D) with Phillips screwdriver until snug. 4. Attach spray hose and counterweight · Connect spray hose (6) to supply hose (4). Install weight (8) on lowest vertical point on spray hose (6).
5. Connect waterlines · Connect waterlines (5A&B) to angle stops. Tighten both ends of waterlines with a wrench until snug. Turn on hot and cold angle stops and check for leaks. · Remove spray head (1) from spray hose (6). Hold tip of spray hose (6). Turn faucet on and let the water run for 60 seconds to flush any debris. 6. Flush spray hose NOTE: Please make sure washer (7) is installed attaching spray head to hose 7. Check for leaks · Check for leaks at the connections. Retighten if necessary.
Replacement Parts 1. Spray Head 2. Check Valve 3. Hose Guide 4. Sprayer Holder 5. Spring 6. Set Screw 7. Sleeve 8. Cap 9. Set Screw 10. Handle 11. Handle Set Screw 12. Handle Button 13. Cartridge Cover 14. Locking Nut 15. Cartridge 16. Base O-Ring 17. Rubber Washer 18. Metal Washer 19. Mounting Nut 20. Mounting Screws 21. Protective Sleeve 22. Washer 23. Hose 24. Check Valve 25. Weight 26. Hot & Cold Waterlines 27. Filter Washer 28. Supply Hose 29.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand.
Restrictions This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at discount outlets, unauthorized dealers, and/or sold on clearance.
Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine, aerators, structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel,etc) of the product to be free from defects in material and workmanship under normal usage for a period of one (1) year.
If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc.
Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.
