R INSTALLATION MANUAL All-In-One Kitchen Set KCA-1102 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Make sure to check off that you have all of the following items Kitchen Sink - KHT400-33 Kitchen Faucet - KPF-1610SS Cut-Out Template Undermounting Hardware Top Mount Hardware Bottom Grid - KBG-T400-33 Drain - ST-1 Prior to Installation: · Make sure that you have all necessary parts by checking the parts list.
Tools you will need: Safety Goggles Drill Silicone Adhesive Jig Saw Phillips Screwdriver Putty Knife Tape Measure Pencil Scissors Screwdriver NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with countertop materials other than wood, marble or granite.
Sink Dimensions: 3 1/2" (88.9mm) 2" (50.8mm) 1 3/8" (35mm) (10mm) 30 1/2" (774.7mm) 9" (228.6mm) 33" (838.2mm) 1 1/4" 3/8" (31.8mm) 3 1/2" (90mm) 17" (431.8mm) 22" (558.8mm) 4 1/2" (114.
Topmount Installation Step 1. Position Template · plate er Tem Pap · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. Step 2. Trace Template · Paper 6 te Templa Trace template on countertop with a pencil.
Step 3. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
Step 4. Attach Mounting Hardware · · Attach mounting hardware to the prongs protruding from the underside of the sink rim. Make sure the hooked side of the mounting clip is facing away from the sink.
Step 5. Apply Silicone or Plumber's Putty · · Clean and dry the surface around the opening of the sink. Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included) underneath the edge of the sink.
Step 6. Secure Sink to Countertop • • • · Insert the sink into the opening, check the alignment of the sink to the cutout in the countertop and press firmly. Tighten the screws in the front of the sink, followed by the ones in the back and on the sides of the sink. Remove excess silicone-based sealant. Allow sealant to set for 30-60 minutes.
Step 7. Install Plumbing Fixtures · · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC certification.
Undermount Installation Step 1.
Step 2. Position template · te Templa Paper · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. Step 3. Trace Template · Paper Trace template on countertop with a pencil.
Step 4. Cut countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material. Step 5. Set up mounting brackets · · 1/2" (13mm) 14 Turn countertop over and align sink with countertop. Decide location for mounting brackets. Mounting holes should be 1/2" from edge of sink.
Step 6. Drill hole in countertop 3/8 · Drill 3/8" diameter x 1/2" deep hole in the countertop. · Insert anchors into drilled holes and lightly tap with a hammer until flush. 1/2 Step 7.
Step 8. Secure sink to countertop · Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly. Step 9. Attach mounting hardware · · Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
Step 10. Install plumbing fixtures · · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Note: Before installation, please check that the drain kit complies with ASME A112.18.2/CSA B125.2 and with CUPC certification. Maintenance Clean your sink on a regular basis with warm soapy water. Rinse the sink after using cleaning products.
Faucet Diagram and Parts List A. Spray Head B. Faucet Body C. Mounting Hardware C1. Rubber & Metal Washer C2. Mounting Nut C3. Mounting Screws D. Quick Connector E. Weight E1. Weight Clip E2. Weight F. 2.
Faucet Dimensions: 10 3/4" 18" (456mm) (274mm) 3 1/2" (88mm) 25° Ø1 7/8" 8 3/4" 2 1/4" (162mm) 90° (56mm) 6 3/8" (221mm) (116mm) 4 1/2" (48mm) Ø2 1/8" (578mm) 22 3/4" 17" (432mm) (54mm) 9/16" - 24UNF Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove mounting hardware (C) from faucet body (B). C Step 2. Installing the faucet assembly Optional No Escutcheon Installation. Insert faucet body through the hole in the sink.
Step 3. Securing the faucet assembly Install the rubber washer and metal washer (C1) onto the threaded mounting shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3). Do not overtighten. C1 C2 C3 Step 4. Securing the faucet assembly Push the quick connector (D) firmly upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made.
Step 5. Securing the faucet assembly Install the weight clip (E1) at the point of the hose marking "weight here". Insert the weight (E2) onto the clip (E1) by sliding it down onto the clip (E1). Weight here E2 E2 E1 Weight here E1 Step 6. Making the waterline connections 1 22 Thread the nut (1) on the supply line onto the outlet of the water supply valve and tighten with a wrench. Do not overtighten.
Step 7. Flushing and checking for leaks Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks. Re-tighten any connections if necessary, but do not overtighten.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Bonnet nut has come loose Remove the cover button. Loosen set screw with hex wrench. Remove the handle. Unscrew cap. Tighten bonnet nut with an adjustable wrench. The aerator has an irregular or reduced The aerator is dirty or mis-fitted Remove the aerator and check for debris.
Codes/Standards Applicable: UP C C R Kitchen Sink Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Kitchen Sink” in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. KRAUS USA has the right to change, modify, and/or update the warranty policy at any time. For the latest, most up to date comprehensive warranty, go to www.kraususa.com/warranty Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by Kraus and all applicable rules, regulations, and legislation pertaining to such installations. Kraus USA recommends that all Kraus products are installed by fully licensed and insured trade professionals with experience in the installation of bathroom and/or kitchen manufactured goods. This warranty does not cover labor charges or costs of removal and reinstallation of said product.
If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8954 Partnersupport@kraususa.com In requesting warranty service, please be ready to provide: 1. 2. Proof of purchase. A description of the problem. Download the Kraus Care & Maintenance Guide at: http://www.kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
R INSTALLATION GUIDE Kitchen Strainer ST-1 / ST-2 / ST-3 / BST-1 / BST-2 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help: Toll-Free: 800-775-0703 or Customerservice@kraususa.
Diagram and Parts List ST-1 A B C D A. B. C. D. E. F. G. H. Strainer Cover Screw Metal Strainer Foam Gasket Rubber Gasket Main Body Drain Gasket Drain Nut A. B. C. D. E. F. G. H.
Diagram and Parts List BST-1 A B C D E F A. Strainer Cover B. Basket C. Screw D. Metal Strainer E. Foam Gasket F. Rubber Gasket G. Main Body H. Drain Gasket I. Drain Nut G H I BST-2 A B C D E F G H I A. Strainer Cover B. Basket C. Screw D. Metal Strainer E. Foam Gasket F. Rubber Gasket G. Main Body H. Drain Gasket I.
Diagram and Parts List ST-3 A B C D E F G H A. B. C. D. E. F. G. H.
Dimensions Ø4 1/2" Ø4 1/2" (115mm) 3 3/4" 3 3/4" (94mm) (94mm) 1 1/2" 11 1/2" NPSM Ø4 1/2" (115mm) 1 1/2" 11 1/2" NPSM Ø4 3/4" (119mm) Model #: ST-1 Dimensions: Ø4 1/2" x 3 3/4" (114mm) 4 1/2" (114mm) 1 1/2" 11 1/2" NPSM Ø4 3/4" (119mm) Model #: ST-2 Dimensions: Ø4 1/2" x 3 3/4" 4 5/8" (116mm) Model #: BST-1 Dimensions: Ø4 1/2" x 4 1/2" 4 1/2" (114mm) Ø4 1/2" R1/2" (13mm) (114mm) 4 1/2" (114mm) 4 1/2" (114mm) 2 5/8" (65.
Step 1.
Step 2. Insert metal strainer into drain hole with foam gasket attached.
Step 3. Using the screw, tighten the metal strainer and main body into place Screw Step 4.
Replacement Parts ST-1 Replacement Parts List A B C D Finish A. Strainer Cover SS* A. Strainer Cover PGM* B. Screw 1 1/4" SS* B. Screw 1 1/4" PGM* C. Metal Strainer SS* C. Metal Strainer PGM* Part # KPU00010 KPU00010-PGM KPU00003 KPU00003-PGM KPU00011 KPU00011-PGM E D. Foam Gasket KPU00005 F E. Rubber Gasket KPU00006 F. Main Body KPU00012 G. Drain Gasket KPU00008 H.
Replacement Parts ST-2 Replacement Parts List A B C D E F G H Finish Part # A. Strainer Cover KPU00010 B. Screw 1 5/8" KPU00013 C. Metal Strainer KPU00011 D. Foam Gasket KPU00005 E. Rubber Gasket KPU00006 F. Main Body KPU00012 G. Drain Gasket KPU00008 H.
Replacement Parts BST-1 Replacement Parts List Finish Part # A B C D E F G A. Strainer Cover KPU00001 B. Basket KPU00002 C. Screw 1 1/4" KPU00003 D. Metal Strainer KPU00004 E. Foam Gasket KPU00005 F. Rubber Gasket KPU00006 G. Main Body KPU00007 H. Drain Gasket KPU00008 I. KPU00009 Drain Nut H I BST-2 Replacement Parts List A B C D E F G H I Finish Part # A. Strainer Cover KPU00001 B. Basket KPU00002 C. Screw 1 5/8" KPU00013 D. Metal Strainer KPU00004 E.
Replacement Parts ST-3 Replacement Parts List A B C D E F G H Finish Part # A. Strainer Cover KP22191 B. Screw KP22198 C. Metal Strainer KP22192 D. Foam Gasket KP22193 E. Rubber Gasket KP22194 F. Main Body KP22195 G. Drain Gasket KP22196 H.
Accessories Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Accessories” in their original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product (Accessories) to be free from defects in material and workmanship under normal usage for a period of one (1) years.
If you are a HOMEOWNER, please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-Free : 800-775-0703 Customerservice@kraususa.com If you are a PLUMBING CONTRACTOR OR TRADE PROFESSIONAL, please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an AUTHORIZED PARTNER, please contact a Partner Support Representative at: Kraus USA, Inc.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
