All-In-One Kitchen Set KCA-1102 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Make sure to check off that you have all of the following items Kitchen Sink - KHT400-33 Kitchen Faucet - KPF-1610SS Cut-Out Template Undermounting Hardware Top Mount Hardware Bottom Grid - KBG-T400-33 Drain - ST-1 Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement.
Tools you will need: Safety Goggles Drill Silicone Adhesive Jig Saw Phillips Screwdriver Putty Knife Tape Measure Pencil Scissors Screwdriver NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with countertop materials other than wood, marble or granite.
Dimensions: 3 1/2" (88.9mm) 2" (50.8mm) 1 3/8" (35mm) (10mm) 30 1/2" (774.7mm) 9" (228.6mm) 33" (838.2mm) 1 1/4" 3/8" (31.8mm) 3 1/2" (90mm) 17" (431.8mm) 22" (558.8mm) 4 1/2" (114.
Topmount Installation Step 1. Position Template · plate er Tem Pap · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. Step 2. Trace Template · Paper Trace template on countertop with a pencil.
Step 3. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
Step 4. Attach Mounting Hardware · · Attach mounting hardware to the prongs protruding from the underside of the sink rim. Make sure the hooked side of the mounting clip is facing away from the sink.
Step 5. Apply Silicone or Plumber's Putty · · Clean and dry the surface around the opening of the sink. Turn the unit upside down to apply sealant. Apply silicone-based sealant (not included) underneath the edge of the sink.
Step 6. Secure Sink to Countertop • • • · Insert the sink into the opening, check the alignment of the sink to the cutout in the countertop and press firmly. Tighten the screws in the front of the sink, followed by the ones in the back and on the sides of the sink. Remove excess silicone-based sealant. Allow sealant to set for 30-60 minutes.
Step 7. Install Plumbing Fixtures · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks.
Undermount Installation Step 1.
Step 2. Position template · te Templa Paper · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop. NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink. Step 3. Trace Template · Paper Trace template on countertop with a pencil.
Step 4. Cut countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material. Step 5. Set up mounting brackets · · Turn countertop over and align sink with countertop. Decide location for mounting brackets. Mounting holes should be 1/2" from edge of sink.
Step 6. Drill hole in countertop · Drill 3/8" diameter x 1/2" deep hole in the countertop. · Insert anchors into drilled holes and lightly tap with a hammer until flush. Step 7.
Step 8. Secure sink to countertop · Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly. Step 9. Attach mounting hardware · · Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
Step 10. Install plumbing fixtures · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks. Maintenance Clean your sink on a regular basis with warm soapy water. Rinse the sink after using cleaning products. Wipe the sink surface with a soft cloth to remove any liquid residue. Do not cut food directly on the surface of the sink.
Diagram and Parts List 1. Spray Head 2. Faucet Body 3. Mounting Hardware A. Rubber Washer B. Metal Washer C. Mounting Nut D. Mounting Screws 4. Supply Hose 5. Hot & Cold Waterlines 6. Hose 7. Washer 8. Weight 9. Hex Wrench 10. Washer (2.2GPM) Please note: This faucet is designed with a 1.8 gpm flow rate in compliance with CEC standards. To adjust the flow rate to 2.2 gpm, replace the washer (7) with the 2.2 gpm washer provided in package.
Faucet Installation Procedure 10 3/4" 274mm 4 1/2" 115mm 8 3/4" 221mm 18" 456mm 6 3/8" 162mm 2 1/8" 54mm Installer Tip Shut off main water supply before installing new faucet 19
1. Remove mounting hardware · Remove the mounting screws (3D), mounting nut (3C), metal (3B) and rubber washer (3A) from the mounting pipe. 2. Install faucet mounting hardware · Insert faucet body (2) into hole in countertop. Install mounting hardware (3A, B, C & D) from underneath the countertop.
3. Secure mounting hardware · Adjust direction of faucet body (2) so that the handle is on the right side of the faucet. Tighten mounting nut (3C) until snug. Tighten mounting screws (3D) with Phillips screwdriver until snug. 4. Attach spray hose and counterweight · Connect spray hose (6) to supply hose (4). Install weight (8) on lowest vertical point on spray hose (6).
5. Connect waterlines · Connect waterlines (5A&B) to angle stops. Tighten both ends of waterlines with a wrench until snug. Turn on hot and cold angle stops and check for leaks. · Remove spray head (1) from spray hose (6). Hold tip of spray hose (6). Turn faucet on and let the water run for 60 seconds to flush any debris. 6. Flush spray hose NOTE: Please make sure washer (7) is installed attaching spray head to hose 7. Check for leaks · Check for leaks at the connections. Retighten if necessary.
Replacement Parts Replacement Parts List Finish/Color Part # CH, SS, MB KP12002 1. Spray Head 2. Check Valve KP12003 3. Hose Guide KP12004 4. Sprayer Holder CH, SS, MB KP12005 5. Spring CH, SS, MB KP12006 6. Set Screw KP12007 7. Sleeve KP12008 8. Cap 9. Set Screw 10. Handle CH, SS, MB KP12009 KP12010 CH, SS, MB KP12011 KP12012 11. Handle Set Screw 12. Cap CH, SS, MB KP12009 13. Cartridge Cover CH, SS, MB KP12013 14. Locking Nut KP12014 15. Cartridge KP12015 16.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand.
Restrictions This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at discount outlets, unauthorized dealers, and/or sold on clearance.
Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine, aerators, structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel,etc) of the product to be free from defects in material and workmanship under normal usage for a period of one (1) year.
If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc.
Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.
