I N S TA L L AT I O N MA N UA L Seda™ Single Lever Vessel Faucet FVS-1820 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc.
Thank you for purchasing Kraus We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future. For more information about Kraus products, please visit our website at: www.kraususa.
10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) 1 3/8” (35mm) ∅ 1 3/4” (∅ 45mm) ∅ 1 15/16” (∅ 50mm) Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800775-0703 for a replacement • Turn off the hot and cold water supply at the angle stops and turn on the old 1 1/4-18UNF-2A faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List E F A D B G C1 C2 C3 A. Faucet Body D. Hot & Cold Waterlines B. Base O-Ring E. Adjustable Aerator (factory-installed) F. Aerator Key C. Mounting Hardware: G. Hex Wrench C1. Rubber & Metal O-Washer C2. Mounting Nut C3.
Faucet Dimensions 2.3” 58mm 1.37” MAX 35 mm 2.28” 58 mm 1.37” 35 mm 1.37” 35 mm 10” 253 mm 5” 129 mm 9” 229 mm 11” 280 mm 7.
Step1 Step2 Step 1: Remove mounting hardware and install waterlines A A Remove mounting hardware (C) from faucet body (A). Place faucet body (A) on a soft cloth. Secure hot & cold waterlines (D) A at the base of the faucet (handtighten, then secure with ¼ turn of adjustable wrench) A. Hot Side: Left B. Cold Side: Right D A2-FNU81-4/1 1 C D Step2 Step 2: Install faucet FENU81-”61/9 C1 Step3 C2 C3 ”8/5 1 ~ ”61/1 1 mm3.
FENU81-”61/9 Step3 Step4 A2-FNU81-A42/1-F1NU81-4/1 1 Step 3: Secure faucet Step1 Step1 A7 ”8/5 1 ~ ”61/1 1 mm3.14 ~ mm72 Step2 Step2 After adjusting direction of faucet body (A), tighten mounting nut (C2) with adjustable wrench. Secure mounting D nut (C2) by tightening mounting screws (C3) with a Phillips head screwdriver A8 B8 C8 D8 C2 C3 A A A D A A A Step4 Step 4: Connect waterlines to main valve A7 ”8/5 1 ~ ”61/1 1 mm3.
Replacement Part List - FVS-1820 1 2 3 4 5 6 7 8 16 13 14 15 9 10 11 12 1. 2. 3. 4. 5. 6. 7. 8. Metal Handle Set Screw Cartridge Cover Cartridge Sleeve Metal O-Ring Rubber Washer Locking Nut Cartridge 9. Base O-Ring 10. Rubber & Metal O- Ring 11. Mounting Nut 12. Mounting Screw 13. Adjustable Aerator 14. Aerator Key 15. Hot & Cold Waterlines 16.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 10 CAUSE Leakage under 9the handle Hexagon Locking nut Nut (7) 11 come loose 12 ACTION has 13 Loosen set screw (2) with hex wrench (17). Remove metal handle (1), cartridge cover (3), cartridge sleeve (4), metal o-ring (5) & rubber washer (6).
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R &T NSF/ANSI 61 ASME A112.18.1M 1.5GPM 5.7L/min maximum TM Water Efficiency KRAUS LIMITED LIFETIME WARRANTY This product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use. WHO IS COVERED BY THE WARRANTY This warranty extends to the original purchaser only.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use. D. Commercial use will automatically void this warranty. E. This warranty is not applicable to Kraus products purchased from an unauthorized seller.
www.kraususa.
