INSTALLATION GUIDE Arcus Single Lever Basin Bathroom Faucet FUS-1011 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List 1 9C 9A 3D 6 9D 2A 9B 9E 9C 4 2B 1 3A 3D 9A 9F 9G 5 6 9D 9B 2A 8 2B 3B 4 9E 9H 7 3C 9F 5 3A 10 9G 7 3B 8 9H 3C 10 3
12 13 Diagram and Parts List Tools you will need: 1 2 3 4 5 6 7 8 1. Faucet Body 2. Deck Plate Assembly (A) Deck Plate (B) Base Plate 3. Mounting Hardware (A) Rubber Washer (B) Metal Washer (C) Mounting Nuts (D) Mounting Screws 4. Hot & Cold Waterlines 5. Cartridge Key 6. Aerator 7. Aerator Key 8. Hex Wrench 9.
4 4 1/8” 1/8” (105mm) (105mm) 3 3 1/4” 1/4” (82mm) (82mm) 1/16”-2 1/16”-2 1/16” 1/16” (1mm-52mm) (1mm-52mm) 5 665/16” 5/16” (160mm) (160mm) 1/2” 1/2” (12.7mm)min (12.7mm)min 12 12º º ØØ221/8” 1/8” (Ø54.7mm) (Ø54.7mm) Ø1 Ø11/4” 1/4” (Ø31.75mm) (Ø31.
step1 step2A step2B Step 1: Remove Mounting Hardware Remove mounting hardware from faucet (3A, B & C) 2A 2B 3A 3B 3C step2A step3 step2B Step 2A: Installing the Faucet With Deck Plate step5 2A 2B 4 For three-hole installation, step7 deck plate (2A), base plate (2B), and silicone sealant are required 4 step3 step2B 6 ste Step 2B: Installing the Faucet Without Deck Plate 7 1 step7 2A 2B 4 6 7 For single-hole installation, deck plate (2A), 2A base plate 2B (2B), and silicone sealant are NOT
step3 Step 3: Install Faucet and Mounting Hardware 1 2A 2B step4 3A 3B 3C step4 Insert faucet body (1) into the hole on the countertop or deck plate assembly (3). Install1 rubber washer (2A), metal washer (2B), and mounting 3C nuts (2C) on mounting screws3D (2D) from underneath the countertop Step 4: Secure Mounting Hardware 1 Adjust direction of faucet body (1).
Step 5: Connect Waterlines to Main Valve step7 step5 4 4 Connect hot & cold waterlines (4) to the angle stops. Tighten with a wrench until snug.
9E 9E 9D 9D 9D 9E 9E 9H 9H 9B 9D 9F 9B 9F 9D 9 9G 9G 1. Place a bead of silicone around the drain opening. Insert drain body (9D), with rubber washer (9E) attached, 3 into the drain hole 9 2. From underneath the countertop, attach concave washer (9F) and mounting nut (9G), and secure tightly to sink 45 5 9C 4 9A 1 9D 9H 9 3. Insert waste stopper (9C) into drain body (9D). Make sure hole on waste stopper (9C) is aligned with 9Hdrain body (9D) opening. 9H 4.
9A 1 tep2A step2B 9B 5. Insert lift pole rod (9A) 2A through the hole in the 2B back of the faucet body (1). From underneath, insert the lift pole rod (9A) into the lift pole extension (9B) by pressing the button on the extension and release 9H 9B step3 9D 1 6. Align drain body (9D) to2A enable drain off pole (9H) 2B and lift pole extension (9B) to engage.
Replacement Parts 1. (A) Index Button (B) Set Screw 2. Metal Handle 3. Cartridge Cover 4. Locking Nut 5. Cartridge 6. Aerator Assembly (A) Aerator Cover (B) Aerator (C) Washer 7. (A) Base Trim Ring 10C (B) Base O-Ring 10A 8. Mounting Hardware 10E (A) Rubber10D Washer (B) Metal Washer 10H 10B (C) Mounting Nut (D) Mounting Screws 10F 9. Deck Plate Assembly 10G (A) Deck Plate (B) Base Plate 10.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE Leakage under the handle Locking nut (4) has come loose 10 Hexagon Nut 9 11 12 13 ACTION Remove handle index button (1a). Loosen set screw (1b) with hex wrench (14). Remove metal handle (2). Unscrew cartridge cover (3) (by hand only).
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1M 1.2GPM 4.5L/min maximum TM Water Efficiency FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. COMMERCIAL WARRANTY Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
