www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Flush angle stops to release any debris prior to installation.
Diagram and Parts List A. Spray Head B. Faucet Body C. Mounting Hardware C1. Rubber & Metal Washer C2. Mounting Nut C3. Mounting Screws D. Quick Connector E. Weight E1. Weight Clip E2. Weight F. 2.5mm Hex Wrench G. 2.
Faucet Dimension 10 3/4" (456mm) (274mm) 18" 3 1/2" (88mm) Ø1 7/8" 25° 8 3/4" (221mm) 6 3/8" (162mm) 90° (56mm) 2 1/4" (116mm) 4 1/2" (48mm) Ø2 1/8" (578mm) 22 3/4" 17" (432mm) (54mm) 3/8” compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove mounting hardware (C) from faucet body (B). C Step 2. Installing the faucet assembly Optional No Escutcheon Installation. Insert faucet body through the hole in the sink.
Step 3. Securing the faucet assembly Install the rubber washer and metal washer (C1) onto the threaded mounting shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3). Do not overtighten. C1 C2 C3 Step 4. Securing the faucet assembly Push the quick connector (D) firmly upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made.
Step 5. Securing the faucet assembly Install the weight clip (E1) at the point of the hose marking "weight here". Insert the weight (E2) onto the clip (E1) by sliding it down onto the clip (E1). Weight here E2 E2 E1 Weight here E1 Step 6. Making the waterline connections 1 Thread the nut (1) on the supply line onto the outlet of the water supply valve and tighten with a wrench. Do not overtighten.
Step 7. Flushing and checking for leaks Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks. Re-tighten any connections if necessary, but do not overtighten.
Replacement Parts Replacement Parts List 1. Sprayer 4 2. Screen Washer 3. Sprayer Hose 7 5 4. Flow Regulator Assembly (2.2GPM) 5. Flow Regulator Assembly (1.8GPM) 9 6 8 8.1 6. Quick Connector Assembly 8.2 10 11 12 3 2 18 1 21 19 22 20 26 13 14 15 16 17 25 24 CH, SFS, SS, SB, MB, KP27087 BG, SFACB, SFACBMB, BGMB** KP27088 BLBG,BLMB,BLSFS, KP27089* BLSS,GRCH, GRSFS,GRSS** KP27075 BL** WH** KP27074 KP27090 CH, MB, SB, SFACB, SFS** KP27220 8.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Bonnet nut (13) has come loose Remove the cover button (17). Loosen set screw (16) with hex wrench (24). Remove the handle. Unscrew cap (14). Tighten bonnet nut (13) with an adjustable wrench. The aerator has an The aerator is dirty or mis-fitted Remove the aerator and check for debris.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
