INSTALLATION MANUAL Natura™ Series White Matte Vessel Bathroom Sink KSV-1MW / KSV-2MW / KSV -3MW / KSV-4MW / KSV-5MW / KSV-6MW www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
Prior to Installation: • Inspect the sink prior to installation to make sure it has not been cracked or chipped during shipping • Observe all plumbing and building codes according to your state requirements • Additional floor and wall preparation may be required to avoid damaging the sink WARNING: This product is fragile and can break, chip, or cause injury if handled recklessly.
Adjustable wrench Tools you will need: J Safety Goggles Drill Pencil Tape Measure Silicone Sealant Silicone Adhesive Phillips sc 4” Hole Saw Parts List (Included) • Cleaning Sponge • Buffing Paper I Dimensions 20” 20” D 1.7”1.7” 14” 14” 15” 15” 4.9” 4.9” KSV-1MW 15” x 4.9” 4 4.9” 4.9” KSV-2MW 20” x 14” x 4.9” 1.7” 1.
Dimensions 19.6” 19.6” 19.6” 1.7” 1.7” 1.7” 15.7” 15.7” 15.7” 3.6” 3.6” 4.3” KSV-3MW 19.6” x 15.7” x 4.3” KSV-4MW 19.6” x 15.7” x 3.6” 16.8” 16.8” 16.4” 16.4” 1.7” 1.7” 16.8” 16.8” 1.7” 1.7” 6” 6” 6” 6” KSV-5MW 16.8” x 16.8” x 6” KSV-6MW 16.
1. Mark Faucet and Drain Hole Location • Place sink in desired location on countertop and mark drain hole and faucet hole centerline with a pencil NOTE: Make sure clearance is suitable for backsplash, faucet, and sink plumbing NOTE: Please allow a minimum of 3.
2. Drill Countertop • Cut the drain opening in the countertop by carefully placing the 4” hole saw on the area marked by pencil 3. Apply Silicone • Check the alignment of the sink to the opening in the countertop.
4. Install Sink • Carefully place the sink on the countertop, align, and press firmly • Allow sealant to set for 30 – 60 minutes Use acetone or rubbing alcohol to remove any excess sealant immediately after application NOTE: 4. Install Plumbing Fixtures • Connect drain to sink. Connect trap to drain.
Codes/Standards Applicable: BATHROOM SINK WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Solid Surface Sink” in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product (Solid Surface Sink) to be free from defects in material and workmanship under normal usage for the lifetime of the product.
COMMERCIAL WARRANTY Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded. No additional warranties, express or implied are given, including but not limited to, any implied warranty of merchantability or fitness for a particular purpose.
R E G I S T E R Y O U R P R O D U C T T O D AY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit http://www.kraususa.com/registration We’re always looking for ways to improve. Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.
INSTALLATION GUIDE Arlo™ Single Lever Vessel Faucet KVF-1200 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-7750703 for a replacement • Turn off the hot and cold water lines at the angle stops and turn on the old faucet to release any built-up pressure • Pre-drilled countertop hole size requirement: 1-3/8” (min) • Max countertop thickness: 2” Diagram and Parts List F A G H B C I D E A. Faucet Body B. Washer C.
Faucet Dimension 6 3/4” [171mm] 5” [128mm] 12 1/8” [307mm] 8 1/4” [209mm] 2 1/4” [57mm] 2” [51mm] 2-9/16-24UNEF-2B Installer Tip: Shut off main water supply before installing new faucet 3
Step 1: Remove washer and lock nut Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove the washer (B) and lock nut (C) from the faucet (A). A B C Step 2: Install faucet A E Before installation, ensure that the flange (E) is placed on the bottom of the faucet assembly (A). Place faucet (A) through the 1-3/8” holes in countertop . Secure the faucet (A) to the countertop using the washer (B) and lock nut (C) provided.
Step 3: Connect waterlines to main valve Attach waterlines(D) to angle stops and tighten until snug. Turn on angles stops and check for leaks (DO NOT TURN FAUCET ON) D Step 4: Install Press pop-up assembly 1 2 3 4 5 6 5 Unscrew the nut (5) from the pop-up body (1), move over the tail pipe (6) and washer (4), then unscrew the coupling nut (3) and remove the washer (2).
Step 4: Install Press pop-up assembly 3 217 8 17/32” 279 10 31/32” 4 Max35 Max1 3/8” 1 2 Place the washer (1) underneath the flange of the pop-up body (2). Slide the pop-up body (2) down through the drain hole on the vessel or basin. From underside, slide the washer (3) against the bottom of the vessel or basin, thread on the coupling nut (4) and tighten. Do not overtighten. Slide the nut (2) over the tail pipe (3). Place the washer (1) into the nut and tighten. Do not overtighten.
Replacement Parts 2 3 1 14 815 32 3/32” 4 1. Index 5 6 194 7 5/8” 2. Set Screw 3. 1Handle 2 7 4. Cap Ø35~Ø38 Ø1 3/8”~Ø1 1/2” Ø35~Ø38 Ø1 3/8~Ø1 1/2” 8 3 5. Bonnet Nut 6. Screw 4 5 7. Cartridge 6 8 8. Aerator 9 4 7 6 8 9. Aerator Wrench 10. Washer 11. Lock Nut 10 s Les n tha m 90m 11 12. Flange 13. Press pop-up assembly 14.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION 10 Leakage under the handle Bonnet nut (5) has come loose Hexagon Nut 9 11 12 Aerator drips or has inconsistent water flow pattern Aerator (8) is dirty or not seated properly Unscrew aerator (8) with aerator wrench (9) Cold and clean Hot out debris Water will not shut off completely Cartridge may need to be adjusted or replac
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R &T NSF/ANSI 61 ASME A112.18.1 1.2GPM 4.5L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
