Kramer Electronics, Ltd.
Contents Contents 1 2 3 4 4.1 4.2 4.3 5 5.1 5.2 5.3 6 6.1 6.2 6.
Introduction 1 Introduction Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world of unique, creative, and affordable solutions to the vast range of problems that confront the video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we have redesigned and upgraded most of our line, making the best even better! Our 1,000-plus different models now appear in 11 groups1 that are clearly defined by function.
Getting Started 2 Getting Started We recommend that you: Review the contents of this user manual Use Kramer high performance high resolution cables1 2 A special CONFIG cable is required to configure and perform firmware upgrades to the machine 3 Overview The RC-7B / RC-7BE is a highly versatile controller interface panel for the control of A/V equipment in any multimedia room, especially the control of a projector or other display device, via RS-232 and/or IR emitter cable.
Overview To achieve the best performance: Connect only good quality connection cables, thus avoiding interference, deterioration in signal quality due to poor matching, and elevated noise- levels (often associated with low quality cables) Avoid interference from neighboring electrical appliances and position the RC-7B / RC-7BE away from moisture, excessive sunlight and dust Caution – No operator-serviceable parts inside unit.
Your RC-7B / RC-7BE 4 Your RC-7B / RC-7BE This section defines the: Front panel of the RC-7B (see section 4.1) Front panel of the RC-7BE (see section 4.2) Side panel of the RC-7B and RC-7BE (see section 4.3) 4.
Your RC-7B / RC-7BE 4.2 Defining the RC-7BE Front Panel Figure 2 and Table 2 define the RC-7BE front panel: Figure 2: RC-7BE Front Panel Table 2: RC-7BE Front Panel # 1 Feature Mounting holes (4) Function For fastening the controller in place 2 Faceplate Attachment Holes (2) For attaching the faceplate to the controller1 3 Configurable Control Buttons (4) 4 CONFIG Port2 on 3.
Your RC-7B / RC-7BE 4.3 Defining the RC-7B / RC-7BE Side Panel Figure 3 illustrates an enlarged view of the side panel of the RC-7B and RC-7BE: Figure 3: Side Panel of the RC-7B and RC-7BE (Enlarged View) Figure 4 defines the side panel of the RC-7B and RC-7BE. For an explanation of how to install and configure, refer to the chapter entitled: Installation of the RC System in the online RC Configuration and Installation guide1. 1 Download it from http://www.kramerelectronics.
Your RC-7B / RC-7BE & / . ) % . 0 )% ).% % 1 ,! &' 234,!56& % . ( % '* !+ ',,) - '() ) %. & '( ) 7 4 !"# $% 7 / $% 8 #3 7 ( *(3 9 #3 % 01 .
Using Your Media / Room Controller 5 Using Your Media / Room Controller1 The example in Figure 5 shows a front view perspective of a typical RC-7BE configuration.
Using Your Media / Room Controller The example in Figure 6 shows a rear view perspective of a typical RC-7BE configuration. It connects to the projector via RS-232.
Using Your Media / Room Controller Figure 7 shows the RC-7BE built into a podium in an auditorium with an overhead projector and a cabinet with a VCR and a DVD inside, all controlled via the RC-7BE. The presenter’s laptop is located on the podium, next to the RC-7BE. It is also controlled by the RC-7BE and is used for presentations and slide shows.
Using Your Media / Room Controller 5.1 Operating the RC-7B / RC-7BE In the example defined in Table 3, the RC-7B buttons are labeled ON, OFF, VOL UP, VOL DOWN on the control buttons and PC, DVD and VCR on the Signal Source buttons and programmed by the system integrator to perform one or more tasks1. Table 3: The Commands Configuration Example ON Button Macro Sequence 1. Power up the projector 4. Brief delay for the projector to heat up 2. Power up the DVD 5. The projector selects the PC input 3.
Using Your Media / Room Controller 5.2 Using the Macro Buttons Pressing any button initiates a macro sequence1, during which the button blinks (as programmed by the system integrator). If during the macro sequence the button blinks faster than usual2, this indicates that a malfunction has been detected3 and the RC-7B / RC-7BE exits the macro sequence. To solve the problem, summon technical help If you want to stop a macro sequence, press and hold that button for 5 seconds.
Flash Memory Upgrade 6 Flash Memory Upgrade The RC-7B1 device firmware is located in FLASH memory, which lets you upgrade to the latest Kramer firmware version in minutes! The process involves: Downloading the upgrade package from the Internet Connecting the PC to the RS-232 port Upgrading the firmware 6.1 Downloading from the Internet You can download the up-to-date file2 from the Internet. To do so: 1. Go to our Web site at http://www.kramerelectronics.com and download the file: “SetKFRXXX-xx.
Technical Specifications Figure 9: The KFR-Programmer Window 2. Select the required COM Port1. 3. Click the File button to select the .s19 firmware file included in the package. 4. Click the Send button to download the file. The Send button lights red. 5. Wait until downloading is completed and the red Send button turns off. 6. Disconnect the power on the RC device. 7. Set the PROGRAM switch to OFF. 8. Connect the power on the RC device.
LIMITED WARRANTY Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase. WHO IS PROTECTED? Only the first purchase customer may enforce this warranty. WHAT IS COVERED AND WHAT IS NOT COVERED Except as below, this warranty covers all defects in material or workmanship in this product.
For the latest information on our products and a list of Kramer distributors, visit our Web site: www.kramerelectronics.com, where updates to this user manual may be found. We welcome your questions, comments and feedback. Safety Warning: Disconnect the unit from the power supply before opening/servicing. Caution Kramer Electronics, Ltd. Web site: www.kramerelectronics.com E-mail: info@kramerel.
