Datasheet

Installation description
Interface Lead Item Nr. 67785
for Audi, Seat, Skoda, VW 2003-
Needed items:
A: Interface Lead.
B: Interface Lead carkit adaptor.
C: Carkit.
Note: The Carkit C and Interface Lead adaptor B are bought sepa-
rately.
Installation:
1st: Remove the key from the ignition barrel. This is done to
avoid error messages on the car electrical system.
2nd. Remove the radio and disconnect the Fakra connector from
rear of the radio.
3rd. Choose mute position. This Interface lead has two mute posi-
tions available. Please chose the right mute position by switching
the bullet connectors on the yellow wires. The correct position can often be seen on a label on the radio.
“MUTE IN 1” is used for older Audi, Seat, Skoda, VW cars.
“MUTE IN 2” is used for newer Audi, Seat, Skoda, VW cars.
4th. Check ignition source. Not all models have an ignition source in the prewired position in the cable set.
Therefore it is possible to disconnect the blue ignition wire from the cable set and connect it to an ignition source
found elsewhere or the red constant 12v wire by using the bullet connectors . Alternatively a IGNIBOX item nr. “I”
can be inserted to generate an artificial ignition.
5th: Check fuse size. The fuse on the Audio2Car cable should not be bigger than the ones used on the wiring
loom supplied with the carkit. The fuses on the Audio2Car cable should be replaced with a size similar to the ones
supplied with the carkit.
Note: Never exceed the Maximum Fuse size for the Interface Lead. See maximum fuse sizes on the last page.
6th. Move connectors from the Fiber-Optics, Accessories and CD-Changer slot on the original car connector to
the connector on the Interface lead. This is necessary to keep full function of the radio.
7th. If the original car connector is fitted with a plug in the Accessories slot this should also be moved to the
connector in the interface lead. The Line-in & mute wires will have to be removed from the Accessories plug de-
livered with the Interface Lead and fitted directly to the connector in the Accessories plug from the car connector.
A step by step guide for removing and re-inserting pins can be seen on the bottom of the next page.
Interface Leads Interface Leads
White
White/Black
Yellow
See our complete Interface Lead program on www.kram.dk
A: Interface Lead
Item number 67xxx
B: Interface Adaptor
Item number DAxxx
C: Carkit
16 pin Connectors
Bullet Connectors
4 pin
Aux
Accessories slot
CD Changer slot
Front view of connector
Fiber Optics slot
How to move Line-in and Mute pins to OEM Accessory plug.
Only applicable for cars equipped with Accessory plug in the car connector.
Step 1:
Remove the pin-holder from the Accessory plug on the Interface Lead by lifting the locking mechanism with a
small screwdriver and pulling the pin-holder outwards:
Step 2:
Remove the pins from the pin-holder. This is done by pressing the pin-lock with a small screwdriver.
Step 3:
Insert the pins into the OEM accessory plug fitted to the connectors on the Interface Lead. Remember to point
the pin-locks in the right direction. White/Black in inserted in position 6, Yellow in position 10 and White in
position 12.
8th. Insert the Interface Lead between the radio and the removed radio connector.
9th. Connect the carkit ‘C’ to the Interface Lead using the Interface Lead adaptor ‘B’. Interface Lead adap-
tors for Music carkit include a 4 pin AUX connector. This is used for connecting an optional Kram AUX solution. By
adding a Kram AUX solution you will achieve a much higher audio quality when playing music from the carkit.
And the music will be heard in all speakers. Please see our website www.kram.dk for further information about
AUX solutions.
10th. Test function and adjust volume. When the Interface Lead is installed correctly it will redirect your call
through the car front speaker. Adjust the volume setting using the carkit and radio volume control. Note that too
high carkit volume will distort the sound.