Manualshelf

Installation Guide

ManualsBrandsKovacs ManualsLightingTraveler 4 Light 14" Wide Pendant
12
INSTALLATION INSTRUCTIONS
Item#P1494-712 (New. 11/19/2019)
READ AND SAVE THESE INSTRUCTIONS
WARNI NG! S HUT P OWE R OFF AT F USE OR CI RCUIT BRE AKE R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
PREPARATION (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box and remove
the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to misplace any small parts necessary
for installation.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 1&Fig. 2)
3. Slide metal tube (J) to the fixture (L) and secure with screws (K).
4. Determine the desired hanging height and thread rods (F1, F2
and F3) to the threaded nipple (I) attached to the metal tube (J).
Then screw loop (H1) to rod (F1). Passing the wires carefully
through each rod as you assemble.
5. Attach quick link (G) to loop (H1) and loop (H2) on the canopy (D),
carefully feed the wire over loop (H1), quick link (G), and loop
(H2).
6. Thread screws (A) into the pre-drilled holes on the circular strap
(B) spaced the same distance apart as the holes on the canopy
(D).
7. Attach the circular strap (B) to the junction box using mounting
screws (C) (Size: #8-32N*L0.5”). The side of the circular strap
marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
8. Connect the electrical wires as shown in fig 3, making sure that all
wire connectors are secured. If your outlet has a ground wire
(green or bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the circular
strap (B) using the green screw provided.
9. Tuck the wire connectors neatly into the ceiling junction box.
COMPLETING THE INSTALLATION (Fig. 1)
10. Raise the canopy (D) over screws (A) and secure with decorative
nuts (E).
11. Slide the candle covers (O) over the sockets (N) of the fixture
body (L).
12. Install (4) four candelabra base bulbs (M) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with
the fixture specification—DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction
box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Set# A-020
-Circular Strap
-Ground Screw
-Mounting Screw*2
Rod# W30-1-66*1(F1)
W30-1-66*2(F2)
W30-H-66*1(F3)
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
IMPORTANT: FIXTURE SHOULD BE INSTALLED
BY A QUALIFIED ELECTRICIAN TO ENSURE
PROPER WIRING AND INSTALLATION.
B
C
E
A
D
G
F1
H1
H2
F2
F3
J
L
O
K
M
N
I
Candle cover#CCV24096P-84

Summary of content (2 pages)