Installation Guide

INSTALLATION INSTRUCTIONS
Item#P1488-248 (Rev. 01/13/2020)
READ AND SAVE THESE INSTRUCTIONS
WARNI NG! S HUT P OWE R OFF AT F USE OR CI RCUIT BRE AKE R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/2
Fig. 1
Fig. 3
Fig. 4
LA-3173E
PREPARATION (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box and remove
the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to misplace any small parts necessary
for installation.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 1&Fig. 2)
3. Determine the desired hanging height and thread rods (F1, F2
and F3) to the threaded nipple (I) on the fixture body. Then screw
loop (H1) to rod (F1). Pass the wires carefully through each rod as
you assemble.
4. Attach the quick link (G) to loop (H1) and loop (H2) on the canopy
(D). Carefully feed the wire through loop (H1), quick link (G) and
loop (H2).
5. Thread screws (A) into the pre-drilled holes in the circular strap
(B) spaced the same distance apart as the holes in the canopy
(D).
6. Attach the circular strap (B) to the junction box using mounting
screws (C) (Size: #8-32N*L0.5”). The side of the circular strap
marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
7. Connect the electrical wires as shown in fig 3, making sure that all
wire connectors are secured. If your outlet has a ground wire
(green or bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the circular
strap (B) using the green screw provided.
8. Tuck the wire connectors neatly into the ceiling junction box and
raise the canopy to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
9. Slide the canopy (D) over the screws (A), and secure with knurled
knobs (E).
10. Dual options: Screw the acrylic rods (J) into the fixture body
(Fig 1) or push end caps (N) into the fixture body (Fig 4).
11. Install (8) eight G9 bulbs (L) (included) up to 60 watts each, or
CFL or LED equivalent, in accordance with the fixture
specification — DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!).
12. Slide the glass shade (M) over the socket and bulb, then twist
to secure it to the socket cup (K).
Your installation is now complete. Return power to the junction
box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY
A QUALIFIED ELECTRICIAN TO ENSURE PROPER
WIRING AND INSTALLATION.
Set# A-020-A
-Circular Strap
-Ground Screw
-Mounting Screw*2
Rod# W30-1-248*1(F1)
W30-1-248*2(F2)
W30-H-248*1(F3)
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
F1
G
H1
H2
E
D
A
C
B
F2
I
J
K
L
M
F3
N
N