Manual

424
Effects
Double Size
119: Rotary SpeakerOD
(Rotary Speaker Overdrive)
This is a stereo rotary speaker effect. It has an internal speaker
simulator that simulates overdrive (recreating the amp distor-
tion) and characteristics of the rotary speaker, producing a very
realistic rotary speaker sound.
a: Sw
This parameter determines how to switch on/off the overdrive
via a modulation source.
When “Sw” = Toggle, overdrive is turned on/off each time the
pedal or joystick is operated.
Overdrive will be switched on/off each time the value of the
modulation source exceeds 64.
When “Sw” = Moment, overdrive is applied only when you press
the pedal or operate the joystick.
Only when the value for the modulation source is 64 or higher, the
overdrive effect is applied.
120: L/C/R Long Delay
This multitap delay outputs three Tap signals to left, right and
center respectively. You can set a maximum of 5,460msec for the
delay time.
a
Overdrive Off, On Switches overdrive on/off
Src Off...Tempo
Selects a modulation source to
switch overdrive on/off
Sw
Toggle,
Moment
Sets the switch mode for overdrive
on/off modulation
b
Overdrive Gain 0...100 Determines the degree of distortion
Overdrive
Level
0...100 Sets the overdrive output level
C
Overdrive Tone 0...15
Sets the tonal quality of the
overdrive
Speaker
Simulator
Off, On
Switches the speaker simulation on/
off
d
Mode Switch Rotate, Stop
Switches between speaker rotation
and stop
Src Off...Tempo
Selects a modulation source for
Rotate/Stop
Sw
Toggle,
Moment
Sets the switch mode for Rotate/
Stop modulation
e
Speed Switch Slow, Fast
Switches the speaker rotation speed
between slow and fast
Src Off...Tempo
Selects a modulation source for
Slow/Fast
Sw
Toggle,
Moment
Sets the switch mode for Slow/Fast
modulation
f
Horn/Rotor
Balance
Rotor, 1...99,
Horn
Sets the volume balance between
the high-range horn and low-range
rotor
Manual
SpeedCtrl
Off...Tempo
Sets a modulation source for direct
control of rotation speed
g
Horn
Acceleration
0...100
Sets how quickly the horn rotation
speed changes
Horn Ratio
Stop,
0.50...2.00
Adjusts the (high-frequency) horn
rotation speed. Standard value is
1.00. “Stop” stops the rotation
h
Rotor
Acceleration
0...100
Sets how quickly the rotor speed
changes
Rotor Ratio
Stop,
0.50...2.00
Adjusts the (low-frequency) rotor
rotation speed. Standard value is
1.0. “Stop” stops the rotation
i
Mic Distance 0...100
Distance between the microphone
and rotary speaker
Mic Spread 0...100 Angle of left and right microphones
j
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 357
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Mic Distance
Mic Spread
Horn/Rotor
Balance
D
-mod
D
-mod
D
-mod
D
-mod
Mode Switch: Rotate/Stop
Speed Switch: Slow/Fast
Manual Speed Control
On/Off
Speaker Simulation
Overdrive
Horn
Rotary Speaker
Rotor
+
a
L Delay Time
[msec]
0...5460 Sets the delay time of TapL
Level 0...50 Sets the output level of TapL
b
C Delay Time
[msec]
0...5460 Sets the delay time of TapC
Level 0...50 Sets the output level of TapC
c
R Delay Time
[msec]
0...5460 Sets the delay time of TapR
Level 0...50 Sets the output level of TapR
d
Feedback
(C Delay)
–100...+100 Sets the feedback amount of TapC
Src Off...Tempo
Selects the modulation source for
the TapC feedback
Amt –100...+100
Sets the modulation amount of the
TapC feedback
e
High Damp [%] 0...100
Sets the damping amount in the
high range
Low Damp [%] 0...100
Sets the damping amount in the low
range
f
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
g Spread 0...50
Sets the width of the stereo image
of the effect sound
h
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 357
Amt –100...+100 Amount of modulation source
C Delay
R Delay
Left
Right
Feedback
Spread
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level