User's Manual

Effect Guide
748
the Send1 (to MFX1) and Send2 (to MFX2) parameters
specified independently for the oscillators
(Program/Sampling mode), timbres (Combination
mode), tracks (Sequencer mode), and audio inputs (in
all modes).
For example, since you can adjust the master effect
send levels for each timbre/track, you can make
settings so that reverb is applied deeply to the piano,
lightly to the strings, and not at all to the bass.
If you’re using insert effects, use the post-IFX Send1
and Send2 to adjust the send amounts.
Program mode
Use the Send1 (to MFX1) and Send2 (to MFX2)
parameters of the P8: “Routing” page, or the Send1
and Send2 parameters of the P8: “Insert FX” page for
the post-IFX1–12 signals, to set the Master Effect send
level.
If you have set Bus Select to L/R or Off, Send1 (to
MFX1) and Send2 (to MFX2) of the “Routing” page are
effective. These parameters can be set for oscillators 1
and 2 individually. (Fig. 2–1a)
Note: You can use the control surface to control Send 1
and 2. For details, see “8–1f: OSC MFX Send” on
page 125.
If you have set Bus Select to IFX1–12, Send1 and
Send2 of the “Insert FX” page for the post-P8-IFX1–12
signals are effective. If you are using the Insert Effects
in chain (series), the Send1 and Send2 parameters for
the post-IFX (last IFX) are effective (Fig 2–1b, 2–1c).
If you have set Bus Select to 1–8, or 1/2–7/8, the
oscillator signals are output directly to AUDIO
OUTPUT (INDIVIDUAL) 1–8.
In this case the Send 1 and Send 2 settings are ignored,
and the Master Effects will not be applied. (page 755)
Send1 responds to CC#93 and Send2 responds to
CC#91 on the global MIDI channel. At this time,
the actual send level uses the value of the Send 1
and 2 settings for Oscillators 1 and 2, multiplied by
the Send 1 and 2 values received via MIDI.
If you have selected “Drums” for Oscillator Mode
(Program 1–1a) of a Program, the “Use DKit Setting”
box (Program 8–1b) becomes available. If you check
this box, Send1 and Send2 levels for each key of the
selected DrumKit become effective. If Bus Select is set
to L/R or Off for a drum instrument key, Send1 (to
MFX1) and Send2(toMFX2) become effective.
If Bus Select is set to IFX1–12, the post-IFX1–12 Send1
and Send2 (Program 8–5a) become effective.
If this is unchecked, Send1 (to MFX1) and Send2 (to
MFX2) (Program 8–1f), and the post IFX1–12 Send1
and Send2 (Program 8–5a) will be valid for all drum
instruments, in the same way as when Oscillator
Mode is Single or Double, or for EXi programs.
Combination and Sequencer modes
Use Send1 (to MFX1) and Send2 (to MFX2) (P8:
“Routing” page) for timbres (Combination) and tracks
(Sequencer) to set the Send1 and 2 levels for each
timbre and track. As with Program mode, if Bus Select
is set to L/R or Off, Send1 (to MFX1) and Send2 (to
MFX2) become effective.
The actual levels use these Send1 and 2 level values,
multiplied by the send level values of oscillators 1 and
2 of the Program P8: “Routing” page.
Send level
For example if you set the program’s OSC1 Send1 (to
MFX1) to 127, Send2 (to MFX2) to 064, OSC2 Send1 (to
MFX1) to 064, Send2 (to MFX2) to 127, and the
combination’s Send1 (to MFX1) to 064 and Send2 (to
MFX2) to 127, the actual send levels of the combination
will be as follows.
Fig. 2–1a