User's Manual
Table Of Contents
- A few words from Greg Mackie.
- Selecting channels for a Mute Group.
- MAIN MIX (L/R) fader.
- Group Master Section.
- BREAK button/indicator
- MONITOR section
- STEREO IN knob
- Meter section.
- FX Master Section.
- Talkback.
- A better way.
- A traditional Monitor Mix.
- Musician's Phones.
- Aux Master AFL buttons and indicator.
- Aux Master.
- Master Control Section
- Further reading about mixing.
- A few more tips on equalization.
- MID EQ (stereo channels)
- Source Mic / Line (stereo channels).
- PFL switch / indicator
- Same as Mono Channels
- Different than
- Channel fader
- Bus Assign switches
- —20 (Signal present) LED.
- Mute button/ indicator.
- Pan.
- FX Send.
- Aux PRE Switch.
- Aux Sends
- EQ (Equalization), Mono Channels
- Comp (Compressor) and indicator.
- Gain Control.
- Mono Channel Strips.
- Channel 25-26 (or Channels 17-18) and Phones
- Musician Phones (AUX OUT 3 OR 4 + L/R INJECT)
- Aux Out.
- Group Out (sub buses).
- Monitor Out.
- Main Out.
- Talkback input.
- Foot Switch input.
- USB Out
- USB In
- USB input / output.
- Stereo input channels.
- Mono input channels.
- Power input connector
- POWER switch
- Power supply section
- Why do we start with the back of the mixer?
- How the band is set up on the mixer.
- The "pusha-bunch-'0' buttons" approach to creating a mute group.
- Un-doing the "pusha-bunch-'0' buttons" approach to creating a mute group.
- Program a Mute Group…
- Rack mounting (MW-2408 only)
- Settings that can be saved
- More on Factory Reset (restoring the factory default settings).
- Other GLOBAL options.
- Recalling a Global Scene
- Saving a Global Scene
- Global menu (scene memory, settings, initialization).
- Locking the state of the feedback suppressor
- Feedback Suppressor: Seting routing options.
- Recalling an Equalizer Setting (continued)
- Recalling an Equalizer Setting.
- Saving Equalizer settings.
- Adjusting (Narrow Mode) Continued
- Adjusting EQ Narrow Mode EQ (31 /9-band).
- Adjusting 9-band EQ (Wide Mode).
- Selecting Narrow or Wide 9-band equalization.
- Recalling a Dynamics preset.
- Saving a Dynamics setting.
- FEEDBACK SUPPRESSOR
- EQUALIZATION
- SoundLink Signal Processing*
- Gee, they don't sound like effects!
- Recalling a DFX preset.
- Saving a Digital Effects setting.
- Using the TAP button to set the delay time.
- Editing an effect
- Applying a Digital Effect
- Selecting the DFX type
- Digital Effects (DFX).
- Saving and Recalling Mute Groups.
- Combining Hard Mutes and Mute Groups.
- Adding to or subtracting channels from a Mute Group.
- Creating a Mute Group.
- "Hard muting".
- OL (Overload) LED.
Hook-up/Back panel Analog Controls Digital Controls
Analog Controls
20 50 100 200 500 1k 2k 5k 10k 20k
WEIGHT WARMTH KNOCK BITE CLARITY
AIR &
SPARKLE
20 50 100 200 500 1k 2k 5k 10k 20k
LO MIDRANGE HI
20
+15dB
50 100 200 500 1k 2k 5k 10k 20k
20
+15dB
50 100 200 500 1k 2k 5k 10k 20k
20
+15dB
50 100 200 500 1k 2k 5k 10k 20k
21
Bass guitar, kick drums, etc. cov-
er the low end. Vocals sit in the
midrange. The cymbals of a drum
kit will carry the high-end sizzle.
Other instruments like piano and
acoustic guitar provide low-mid
warmth.
Since most instruments cov-
er a wide range of frequencies,
it’s nearly impossible to settle
on a single EQ control to repre-
sent an instrument, but rather a
range. Another way to approach
EQ is by the effect that various
frequency ranges affect instru-
ments’ tone, shown in the chart
below.
To quote Izotope, a company
we really trust (https://www.
izotope.com/en/learn/princi-
ples-of-equalization.html)
“Remember that equalization is a
problem-solving procedure. A good
better to cut than to boost, mainly
because the human ear is more
used to a reduction than to an
augmentation in intensity of fre-
quencies.”
Above is the frequency dis-
tribution of SoundLink mono
channel EQ.
There two con-
trols for
MID?
Because they
adjust different
things: One
knob for amount
(±dB), and one
knob for
FREQ
(frequency).Its center frequency
can be moved anywhere from
Hz to ,Hz which makes
it much more useful. At Hz,
it can work on the tone of guitar,
approach to equalization is
to listen carefully to the so-
loed track and come up with
a list of things you might
want to improve or correct.
“Always keep your equal-
ization boost/cut at a rea-
sonable level. As a general rule,
avoid cutting or boosting by more
than 6 dB unless absolutely neces-
sary. If for some reason you see that
some of your EQ settings go over
this limit try to question why and
see if there is a better solution to the
problem such as mic placement.
“Also keep in mind that you will
have to make more small adjust-
ments every time you add tracks to
the mix since the frequencies and
respective ranges of the other in-
struments affect the way an instru-
ment sounds.
“As a general rule, it is always
upped bass guitar, percussion,
low men's voice, etc.
At ,Hz, it's right in the
middle of the vocal range
At K, you can enhance or
reduce acoustic guitar, women's
vocals, and percussion such as
snare, high-hat etc.










