Operation Manual

Using KARMA
230
5. Inthetabsattheleft,selectModuleA.
6. Set“MIN,”“MAX,”“VALUE,”“ASSIGN,”and
“POLARITY.”
7. MakesettingsinthesamewayforModuleB,C,
andD.
The“A S S I G N” settingsformoduleA,B,C,andDare
usedwhenMODULECONTROLissettoA,B,C,orD
respectively.
Withtheappropriate“A S
S I G N ” settings,aGE
realtimeparameterof(forexample)moduleAcan
controlledindependentlybyMasterandModuleA.
Forexampleyoucanmakesettingssothatthe
SwingparameterofadrumGEonmoduleAis
controlledinMASTERbyslider1overarangeof0–
50%,andinMODUL
EAbyslider1overarangeof
50–100%.
Master:0–50%
ModuleA:50–100%
Inthiscase,ifyouswitchMODULECONTROL
betweenMASTERandAwhileusingslider1to
controltheparameter,theparameterwilloperatein
itslast‐controlledstate.IfyousetSwingto0%in
MA
STE
R,andthenswitchtomoduleA,Swingwill
remainat0%aslongasyoudon’tmoveslider1.
HoweverSwingwillchangeonceyoumoveslider1
tocontroltheparameterintherangeof50–100%.
1. SetMODULECONTROLtoMASTER,andset
slider1totheminimumposition.→“Swing”
operatesat0%.
2. ChangeMO
DULECONTROLtoA.→“Swing”
operatesat0%.
3. Moveslider1tothemaximumposition.→
“Swing”operatesat100%.
Theinternalsettingsareautomaticallycontrolledso
thatthephrasebeinggenerateddoesnotchange
abruptly.IntheaboveexamplewhenyouuseMASTER
to
set“Swing”to0%andthenswitchtomoduleA,the
displayedindicationis50–100%buttheparameteris
actuallyoperatingatavalueof0%.Inthisway,you
needtobeawarethatthedisplayedindicationmaynot
matchtheactualresult.
Perf RTP (Perf Real-Time Parameters)
Inthesamewayasforaprogram,KARMAparameters
otherthanGErealtimeparameters(e.g.,KARMA
moduleparameters)canalsobeassignedto
controllers.
ThesesettingsarevalidwhenMODULECONTROLis
settoMASTER.
1. GototheCombinationP7:KARMA–PerfReal‐
TimeParameterspage.
Inthesamewayasforaprogram,se
t“Group,”
“P
arameter,”“Min,”“Max,”“Value,”“A s s i gn , ” and
“Polarity.”Inacombination,youcanusethefour
KARMAmodulesA,B,C,andD.
Turnon(check)the“A , ” “B,”“C,”and/or“D”boxesto
selectthemodule(s)youwanttocontrol.
Intheaboveexample,KARMAREALTIME
CONTROLSsw
itches1,2,3,and4arecontrollingthe
Run/MutesettingofmodulesA,B,C,andD
respectively.
Dynamic MIDI settings
Youcanmakethesesettingsinthesamewayasfora
program.Formoreinformation,see“DynamicMIDI
Sources&Destinations”onpage 1109oftheParameter
Guide.
Naming the KARMA RTC sliders 1–8 and switches
1–8 for MASTER and module A–D
Inthesamewayasforaprogram,youcanselectnames
fortheKARMACONTROLSslidersandKARMA
SWITCHES.Thesesettingsaresavedaspartofthe
combination.
KARMA REALTIME CONTROLS
KARMA SCENES
KARMA SWITCHES
KARMA CONTROLS
123
4
567
8
MODULE
CONTROL
MASTER
A
B
C
D
KARMA module [D]
KARMA module [C]
KARMA module [B]
KARMA module [A]
MODULE
CONTROL
MASTER
A
B
C
D
KARMA module [D]
KARMA module [C]
KARMA module [B]
KARMA module [A]
KARMA REALTIME CONTROLS
KARMA SCENES
KARMA SWITCHES
KARMA CONTROLS
123
4
567
8