Operation Manual

Using KARMA
224
2. Specifythecopy‐sourcemode,bank,andnumber.
IfyouwanttocopytheGErealtimeparametersettings
andscenesettingsfromthecopy‐sourceprogram,
choosethe“GERTPControlSettings&Scenes”option
(checked).
Ifyouwanttocopyperformancerealtimeparameters
settingsandfrontpanelsettingsfromthecopy‐source
progr
am,choosethe“Perf.RTP&PanelSettings”
option(checked).
Ifyoutocopythepadsettingsfromthecopy‐source
program,choosethe“Pads”option(checked).
3. PressOKtoexecutethecopy,orpressCancelif
youdecidetocancel.
Setting KARMA’s keyboard zone
Here’showtospecifythezoneofkeysthatwilltrigger
KARMA.Forexampleyoumightmakesettingssothat
thekeysatthebottomofthekeyboardwilltrigger
phrases,andkeysabovethisrangecanbeplayed
normally.
1. GototheProgramP7:KARMA–GESetup/Key
Zonespage.(Seethediagra
minstep1of
“SelectingaGE”)
2. UsetheKeyZonesBottomandToptospecifythe
keyzone.
Anynotesthatfallwithinthisrange—includingboth
playingonthelocalkeyboardandnotesreceivedfrom
MIDIIN—willbesenttotheKARMAmodule.
Intheexampleshownabove,thenotesfromC‐1
throughB3arebeinginputtotheKARMAmodule.
WhenyouplayB3oralowernote,KARMAwill
generateaphraseorpattern.
3. If“ThruInZone”and“ThruOutZone”areon
(checked),thenotesyouplayonthekeyboardwill
playinadditiontotheph
raseorpatterngenerated
byKARMA.
Thesetwofieldsarethesettingsforinsideandoutside
thekeyzone.
Youcanuse“TransposeInZone”and“TransposeOut
Zone”totransposethenotesplayedonthekeyboard
insemitonesteps.
Intheexampleshownabove,theB3andlowerkeys
willcontrolon
lythephr
aseorpatterngeneratedby
KARMA,andtheC4andhigherkeyswillbeusedfor
manualplayingonthekeyboard.Use“TransposeOut
Zone”toadjustthepitchofthemanually‐played
region.
KARMA module MIDI filtering and CC
offset
1. GototheProgramP7:KARMA–MIDIFilter/CC
Offsetpage.
Receive MIDI Filter
Thisspecifieswhetherfilteringwillbeappliedtothe
MIDIcontroldatareceivedbytheKARMAmodule.If
anitemison(checked),thecorrespondingdatawillbe
received.
WhenKARMAison,MIDIcontroldatareceivedby
theKARMAmoduleissentdirectlytothetone
generator.Ifthissettingisof
f(unchecked),thatdata
willnotbesenttothetonegenerator.
Intheexampleshownabove,damperpedalmessages
areenabledwhenKARMAisoff,anddisabledwhenit
ison.
Transmit MIDI filter
Thisspecifieswhetherfilteringwillbeappliedtothe
MIDIcontroldatageneratedbytheGEselectedforthe
KARMAmodule.Ifanitemison(checked),
transmissionisenabled.
Normallyyouwillleavetheseitemson.Ifyoudon’t
wanttousethepitchbendorothercontrolchangedata
generatedbythesel
e
ctedGE,turntheseitemsoff
(unchecked).
Intheexampleshownabove,pitchbenddata
generatedbytheGEwillnotbetransmitted.
CC Offset
Usethisifyouwanttocontroltheeffectsorthesound
oftheprogramwhileKARMAison.Forexample,you
mightusethistodecreasethebrightnessofthesound
orraisetheresonanceofthesoundinconjunctionwith
thephrasethat’sbeinggenerated.Alternatively,you
mightusethistocontroleffe
cts,forexampleby
turningonadelayeffectinconjunctionwitha
generatedphrase.
Use“CCNumber”tospecifytheMIDIcontrolchange
number.ChooseoneoftheCCnumbersinthe70’s
whichcontrolthesound,oranAMSorDmodsource
(see“7–2c:CCOffset”onpage
111oftheParameter
Guide).
Intheexampleshownintheprecedingpage,CC#74
andCC#71arecontrollingfiltercutoffandresonance
level.