User Manual

9
The metronome
TheC1/C1Airisequippedwithametronome,whichcanbe
changedtoabellsound,whichisconvenientforpracticing.
Turning on/o the metronome
1. Press the METRONOME buon.
The buon lights up, and the
metronome starts.
2. To stop the metronome, press the METRONOME buon
again.
Thebuonturnso.
Specifying the tempo
Regardless of whether the
metronome is turned on or
o, press the DISPLAY but-
ton,andthen,aftertheTEMPOLEDislit,pressthe+or
–buontochangethetempo.
Theseingrangeis𝅘𝅥=40–240.
Toreturntothedefaultseing(120),simultaneouslypress
the+and–buons.
 ThetempocanalsobespeciedintheMetronomeSet-
tingsMode.
Specifying the Time Signature, Volume, Accent
Sound, Tempo and Sound
1. Hold down the METRONOME buon until the Met-
ronome Seings Mode is entered.
TheMETRONOMEbuonblinks.
2. Press the appropriate buon shown below to select a
parameter and display its seing in the display, and
then press the + or – buon to change the seing.
Torestorethedefaultseing,simultaneouslypressthe
+and–buons.
Hold down
the Metronome Settings Mode
Time Signature
Volume
Sound
TempoAccent Sound
Setting
(Button)
Setting Range Default
setting
AccentSound
( )
oFF( noaccentsound ),
on1(emphasizedsoundfortheaccentbeat),
on2( bellsoundfortheaccentbeat )
o
Tempo( )
40–240(sameastemposeing) 120
Sound( )
1(acoustic),2(electronic) 1
TimeSignature
(PART1)
02(2/4),03(3/4),04(4/4),06(6/4) 04
Volume
(PART2)
01–13 10
3. After changing the seing, press the METRONOME
buon to exit the Metronome Seings Mode.
WhentheMetronomeSeingsModeisexited,theMET-
RONOMEbuonreturnstoitslightingstatus(litornot
lit)beforetheMetronomeSeingsModewasentered.
Byperformingthe“Saveparameterseings”(seepage
13) operation before the C1/C1 Air is turned o, the
seingsspeciedforthesound,accentsoundandvol-
umebeforetheC1/C1Airwasturnedocanbesaved
asthedefaultseings.
Touch settings
Thekeyboardsensitivity,ortouch,canbeprogrammed.
To change the seing, hold down the TOUCH buon and
press the + or – buon beside the display.
02
01
03
05
Loud
Loudness
Quiet
Quiet
Loud
Playing strength
04
Display Touch sensitivity
001 Light.Loudnotescanbeproducedevenbyplay-
inglightly.
002 Normal.Normalpianotouch.
003 Heavy.Loudnotescanbeproducedonlybyplay-
ingveryhard.
004 Stable. Sensitivity variations are reduced, and a
relativelystablesoundisproduced.
005 Steady.Steadynotesareproduced,likewithanor-
gan,regardlessoftheforceusedtopressthekey.
Whentheinstrumentisturnedon,thetouchseingis
resetto002(Normal).
Theseingsareappliedtoallsounds.
Transpose
Insomecases,asongmaybewrieninadicultkey(e.g.,
many black keys), or you may wish to shift the pitch to
match anotherinstrumentor vocalist.Insuch cases,you
cantranspose(shiftthepitch)sothatyoucanuseaneasier
ngering,orusethesamefamiliarngeringtoplayatadif-
ferentpitch.ThisiscalledtheTransposefunction.
For example if you transpose upward by one semitone,
playingthenotesshownatthelowerleftwillproducethe
pitchesshownattheright.
While holding down the TRANSPOSE buon, press the
keyboard key (F#6–F7) for the desired transposition.
IfakeyboardkeyotherthanC7ispressed,theTRANSPOSE
buonlightsuptoindicatethatthekeyboardistransposed.
Thepitchoftheentirekeyboardis transposed according
tothepitchofthepressedkeyboardkeyinrelationtoC7.
To return to the original pitches, hold down the TRANS-
POSE buon and press the C7 key.
TheTRANSPOSEbuonturnso,andtranspositioniscanceled.
C4
C7
F7
F 6
key Effect
F
#
6 - B6 6–1semitonesbelow
C7 Standardpitch
C
#
7 - F7 1–5semitoneshigher
Whentheinstrumentisturnedon,thetransposingis
reset.