User Manual

131
Appendices
Restoring the factory settings
Loading the preloaded data
The original preload data is backed up in the KROSS, so you
can restore any or all of the Programs, Combinations, Drum
Kits, User Arpeggio Patterns, and Global settings to their
original factory settings.
Note: The original demo songs can be re-loaded at any time.
For details, please see “About the data loaded by All Preload
PCG”.
User banks and user patterns where preload data has not
been loaded will remain unchanged. If you want to erase
user banks or user patterns, initialize the KROSS and then
load the preload data. For more details, please see
“Initializing the system” on page 132.
Never turn off the power while the data is being loaded.
Before you load the preload data, go to the GLOBAL>
SYSTM page, and uncheck the “Memory Protect”
settings for the data that you want to load. If you
execute this procedure with these settings checked, the
data will not be loaded.
Loading the preloaded data will overwrite the contents
of the internal memory. If you want to keep the existing
data that is stored in internal memory, use “Save All
(PCG&SNG)” or “Save PCG” to save your data to the
SD card before you continue.
This cannot be used while the SD card's Automatic
loading at start-up is in progress, nor while the audio
recorder is recording or playing back.
1. Access the GLOBAL> BASIC page.
Hold down the EXIT button ( ) and press the
SEQ button ( ) to enter Global/Media mode.
If the GLOBAL> BASIC page is not shown, press the
EXIT button.
2. Select the Load Preload/Demo Data function.
Press the FUNCTION button. Use the PAGE– (▲) and
PAGE + (▼) buttons to select Load Preload/Demo Data,
and press the MENU (OK) button. A dialog box will
appear.
3. As the Kind, use the VALUE dial etc. to choose All
(Preload PCG and Demo Songs).
4. Press the MENU (OK) button to load the preload
data. If you decide not to load the preload data, press
the FUNCTION (CANCEL) button.
When you press the MENU (OK) button, a dialog box
will ask you for confirmation. Press the MENU (OK)
button to execute loading.
About the data loaded by All Preload PCG
When you execute All Preload PCG, the following data will
be loaded:
• Program: Bank A, B, C, D, E, F
• Combination: Bank A, B, C
• Favorite bank: A, B, C, D
• Drum Kit: 00(INT)–51(INT)
• User Arpeggio Pattern: 0000–1023
• Global Setting
If you execute All (Preload PCG and Demo Songs), the
demo songs will be loaded as well as the data above.
• Demo Song: S000–002
Note: As with the other user songs, the Demo Song data will
not remain in Sequencer mode when you turn off the power.
You’ll need to load it again if necessary.
Initializing the user bank
Here’s how to initialize a program or combination in the user
bank.
1. Select the user bank program or combination that you
want to initialize.
Use the CATEGORY dial to select the USER category,
and use the VALUE dial to select the program or
combination; then press the MENU button.
2. Select the Write/Initialize Program or Write/Initialize
Combination function.
Press the FUNCTION button. Use the PAGE– (▲) button
to select the function above, and then press the MENU
(OK) button. A dialog box will appear.
3. Use the cursor buttons ◄►▲▼ to select Initialize,
and press the ENTER button.
4. Use the cursor buttons ▼ to choose This/Bank/All,
and press the ENTER button to select it.
This: Only the selected program or combination will be
initialized.
Bank(UA...UD): Initializes the programs or combinations
of the selected bank.
All: All programs or combinations in USER bank will be
initialized.