User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Error and confirmation messages S (Sample–Source)
277
• Either delete an existing file or directory, or Open a
directory to move down one level before executing once
again.
S (Sample–Source)
Sample data used in other sample(s)
Continue?
Meaning: Other sample(s) use the same sample data as the
sample that you are editing. To continue editing, press the
OK button.
Sample L and R are identical
Meaning: The edit operation could not be executed because
the destination (save location) L and R sample numbers are
identical.
• Select different sample numbers for L and R of the
destination (save location).
Sample length is shorter than minimum
Meaning: You attempted to execute an editing operation
that would make the sample data shorter than 8 samples.
• Change the editing range so that the sample data will be
longer than 8 samples.
Sample used in other multisample(s)
Continue?
Meaning: The sample you are editing is used by other
multisamples. To continue editing, press the OK button.
Selected file/path is not correct
Meaning: When loading a divided .PCG file, you attempted
to load a .PCG file of the same name that was not divided or
had differing contents.
• Load the correct .PCG file.
Meaning: When loading a KSF file that was split across
multiple media, the order in which you attempted to load the
files was incorrect.
• Load the KSF file in the correct order. To view the file
number order in which the KSF files were saved, you can
check the Translation page menu command. (The
sample name and number of the first KSF file will be
displayed.)
Slice point over limit
Can’t divide
Meaning: When using the Sampling mode Time Slice or
Time Stretch commands, the Slice setting would divide the
sample into more samples than the maximum possible
number (1000), and thus Divide cannot be executed.
•Use Link to connect any Index that you do not require,
and then execute Divide.
Source file is not 44100Hz or 48000Hz
Can’t convert
Meaning: When executing the Disk mode Utility page menu
command Rate Convert, you selected a WAVE file of a
sampling rate other than 44.1 kHz or 48 kHz.
• You cannot convert WAVE files other than 44.1 kHz or
48 kHz.
Source IFX is all empty
Meaning: This message will appear when you execute Copy
Insert Effect or Copy From Program if there is no insert
effect to be copied.
Source is empty
Meaning: No data exists in the track or pattern that you
specified as the source.
• Specify a track or pattern that contains musical data.
Source sample is empty
Meaning: When executing Insert, Mix, or Paste, the source
sample is empty.
• Execute the Copy operation before executing Insert, Mix,
or Paste.
T (The clock–/TEMP folder detected)
The clock battery voltage is low. Please
replace the battery, and set the date and
time in Disk mode.
Meaning: The battery for the clock/calendar function has
run low, and needs to be replaced. Your Korg Distributor can
help you find a service center to replace the battery.
The data on the medium will be lost. Are
You Sure?
Meaning: When you format a disk, all of the data on the
disk will be erased. Make sure that you have any data backed
up before proceeding! To proceed with formatting the disk,
press OK.