User Manual

Table Of Contents
Effects selection and routing Using effects in Programs
215
these effects would be inserted into the output of the
oscillator.
5. Make settings for Pan (CC#8), Bus Sel. (Bus Select),
Send 1, Send 2, REC Bus and Ctrl Bus for the sound
after it has passed through the insert effects.
If you’ve specified a chain, the settings that follow the
last IFX in the chain will be valid (except for “Ctrl Bus”).
Pan: Sets the pan of the IFX output.
Bus Sel. (Bus Select): Specifies the output destination.
Normally you will set this to L/R. If you wish to send the
sound that has passed through the insert effects to
AUDIO OUTPUT (INDIVIDUAL) 1–4, select 1–4, 1/2,
or 3/4.
Send 1, Send 2: Sets the send levels to the master effects.
For this example, set this to 127.
Ctrl Bus: The FX Control Buses lets you create effects
“sidechains.” Sidechains let you control an effect with
one audio signal (the sidechain), while the effect
processes a completely different audio signal. This is
convenient for use with vocoders, compressors and
limiters, gates, etc. For more information, see “FX
Control Buses” on page 862 of the Parameter Guide.
REC Bus: The sound processed by the insert effect will
be sent to the REC bus. In the P0– Audio Input/Sampling
page, you can set the Sampling Setup Source Bus to a
REC bus, and sample the signal that is sent to the REC
bus. Use this if you want to sample only the sound of an
audio input source being processed by an insert effect
(and not sample the sound of the oscillator output).
Alternatively, the direct sound from the audio inputs can
be mixed with the sound processed by an insert effect,
sent to a REC bus, and sampled.
6. Go to the P8: Insert Effect– Insert FX page, and edit
the parameters of the insert effect you selected.
Press the IFX 1–12 tab, use the tabs at the left to select
IFX1–12, and edit the effect parameters.
Effect 1 On/Off: Turns the insert effect on/off. This is
linked with the on/off setting in the Insert FX page.
P (Effect Preset): Selects an effect preset. The
KRONOS’ internal memory contains “effect presets”
which are parameter settings for each effect from 001:
St.Dyna Compressor through 197: Rotary Speaker Pro
CX Custom.
Effect parameters you edit are saved as part of each
program, but effect presets allow you to save favorite
parameter settings for each effect. For more information,
see “Effect Presets” on page 223.
For details on the individual effects, see:
“Dynamics” on page 891 of the Parameter Guide
“EQ and Filters” on page 904 of the Parameter Guide
“Overdrive, Amp models, and Mic models” on
page 920
of the Parameter Guide
“Chorus, Flanger, and Phaser” on page 929 of the
Parameter Guide
“Modulation and Pitch Shift” on page 942 of the
Parameter Guide
“Delay” on page 963 of the Parameter Guide
“Reverb and Early Reflections” on page 985 of the
Parameter Guide
“Mono-Mono Serial” on page 990 of the Parameter
Guide
“Mono/Mono Parallel” on page 1006 of the Parameter
Guide
“Vintage” on page 1021 of the Parameter Guide
Master effects
The input levels to the master effects are set by the Send 1 &
2 levels. If Send 1 & 2 are zero, the master effects will not
be heard. Send 1 goes to MFX1, and Send 2 goes to MFX2.
1. Go to the Program P9: Master/Total Effect– Routing
page.
2. In MFX1 and MFX2, select the type of each master
effect.
P (Eect preset)Eect On/O
Eect ParametersWet/Dry