User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Introduction to KRONOS
12
Other objects
j: Radio button
Press a radio button to select one value from two or more
choices.
k: Check box
Each time you press a check box, it alternates between the
checked (red) and unchecked states.
The parameter will be active if it is checked, and inactive if it
is unchecked.
Patch panel
The MS-20EX and MOD-7 use on-screen patch panels to
route audio and control signals.
To make a connection between two patch points:
• Touch one of the two jacks (either input or output),
and drag your finger across the screen to the second
jack.
A yellow line appears as you drag across the screen, and is
replaced by a patch cable once the connection is made.
To delete a connection between two patch points:
• Touch the input jack, and drag off of the jack.
The selected connection will be deleted.
Program Play page Overview/Jump graphics
The main P0 Play page in Program Mode features an
interactive overview of the most important parameters, such
as oscillators, filters, envelopes, LFOs, and so on. Just touch
any of these overview areas, and you’ll jump to the
corresponding edit page.
CX-3 Drawbars
You can edit CX-3 drawbars just as you would other slider
controls, by touching and dragging the individual drawbars
one by one.
There’s also a special feature that allows you to drag shapes
across all of the drawbars at once. To use this feature, enable
the Drag Across Drawbars check-box in the lower right of
the P: 5–2: Drawbars page. Then, drag a shape across all of
the drawbars horizontally.
Toggle buttons
This type of button will change its function or switch on/off
each time it is pressed.
Play/Rec/Mute buttons in Sequencer mode:
Solo On/Off buttons in Sequencer mode:
Effects On/Off buttons:
j: Radio button
k: Check box