User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Sampling in Sequencer mode In-Track Sampling
159
Sampling in Sequencer mode
In Sequencer mode, you can sample just like in Program and
Combination modes, but there’s an additional option unique
to Sequencer mode: In-Track Sampling.
In-Track Sampling lets you sample an audio source that’s
being played along with the song. During the sampling
process, the system will automatically create a Program to
hold the new sample, and MIDI notes to play it in sync with
the song. You might use this to record a vocal or guitar part,
for instance.
In-Track Sampling
In this example, we’ll show the sound of a guitar connected
to the AUDIO INPUT 1 jack can be added to your song.
1. In Sequencer mode, select the song to which you want
to add the guitar sound.
You can either create a song, or use Disk mode to load a
previously-created song.
2. Connect your guitar to the rear panel AUDIO INPUT
1 jack.
Press the AUDIO INPUT MIC/LINE switch inward to
select the LINE position, and set the LEVEL knob at
about the center.
If you connect a guitar with passive pickups (i.e., a guitar
that does not contain a preamp), you will be unable to
sample it at the correct level because of the impedance
mismatch. Such guitars should be routed through a
preamp or an effect unit.
3. Go to the Sequencer P0: Play/REC– Audio
Input/Sampling page.
4. We will be modifying the Audio Input settings, so turn
the Input “Use Global Setting” off.
5. Choose the Auto HDR/Sampling Setup page menu
command.
The dialog box will appear.
6. Choose “In-Track Sampling.”
7. Make the following settings for “In-Track Sampling.”
Source Audio: Audio Input 1/2
The input from the AUDIO INPUT 1 and 2 jacks will be
sampled.
Mono–L/Mono–R/Stereo: Mono-L
The sound will be sampled in mono.
To: as desired
The track you want to use for In-Track Sampling. MIDI
note data to trigger the sample will be recorded in the
track you selected.
Program: as desired
The convert-destination program number. When
sampling is completed, a new multisample will be
automatically created, converted to a program, and
assigned as the program for the track.
8. Press the OK button to execute the command.
Preparations for In-Track Sampling are now completed.
Let’s take a look at the settings that were made.
– Audio Input –
INPUT1
Bus Select (IFX/Indiv.): Off
Pan: L000
Level: 127
REC Bus: 1/2
The input from AUDIO INPUT 1 will be sent to REC
bus.
– RECORDING LEVEL–
Recording Level: 0.0
This is the default setting for sampling.
– Sampling Setup –
Source Bus: REC 1/2
The sound sent to REC 1/2 bus will be sampled.
Trigger: Sampling START SW
Press the SAMPLING REC switch to enter record-
standby mode. Then press the SAMPLING
START/STOP switch to start sampling.
Save to: RAM
Th
e sample will be recorded to RAM memory.
Mode: L-Mono
The sound of the internal left channel will be sampled in
mono.
9. For this example, change the settings as follows.
Pan: C064
“Trigger”: Threshold, “Threshold Level”: as desired
“Sample Time”: as desired
10.Play your guitar at the volume that you will be
recording.