User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Sampling (Open Sampling System)
142
Creating multiple samples
In the example procedure described above, several indexes
were created (by pressing the Create button several times),
and then samples were assigned to each Index.
As an alternative method, it is also possible to create one
index, sample into it, and then repeat these two steps.
1. Press the Create button once to create an index.
2. Record a sample.
The recorded sample will automatically be assigned to
the index you created in step 1.
3. Repeat steps 1 and 2.
This is an efficient way to record multiple samples.
Assigning samples to the pads
In Sampling mode, you can use the pads to play samples
directly. The on-screen pads are available on the
P4:EQ/Controls page. USB controllers, MIDI input, and the
local keyboard can all control the pads as well; for more
details, see “Playing the pads” on page 39.
By default, pads 1–8 correspond to the C2–G2 keys. For
example, the default Index setting for 001/008 sets OrigKey
and Top Ke y to C2. The assigned sample will sound when
you play the C2 key. The same sample will also sound when
you play pad 1.
Similarly, if you assign samples to Index 002–008, the
samples that sound when you play the C#2–G2 keys will
also sound when you play pads 2–8.
For each pad, you can change the note numbers used to play
samples.
For example, you might assign the infrequently-played
highest eight notes of the keyboard to correspond to the
pads. To make the setting, select the note number field, and
play the desired key while holding down the ENTER switch.
On-screen pads in Sampling mode
Assigning samples to the pads
Keyboard range
C4 key
Index02 Index03...Index08Index01
By holding down the ENTER switch and playing a note, you can select the corresponding
index, and the specified key will be the base key and will be shown in blue.
Pads 1...8 correspond to C2...G2.
On-screen Pads are available on the P4:EQ/Control page.
Original Key (currently selected
Original Key is displayed in red)
Index zone (currently
selected Index is reversed)