User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Audio recording Other variations of audio track recording
105
Other variations of audio track recording
Bouncing audio tracks
Bouncing lets you combine two or more tracks into either a
single mono track, or a stereo pair.
In this example, we’ll show how audio tracks 1 and 2 can be
bounced to audio track 3.
Before you proceed, you’ll need to record onto audio tracks
1 and 2. To record on audio track 2, make settings as
described under “Recording Setup” on page 99, but in the
P0: Play/REC– Audio Track Mixer page, set Audio Track 2
REC Source to REC1, and in the P0: Play/REC– Preference
page, set “Track Select” to Audio Track 02.
Setup
1. In the P0: Play/REC– Audio Track Mixer page, set up
both audio tracks 1 and 2 as shown below:
Play/Rec/Mute: Play
Solo On/Off: On
Pan: L000
Volume: 127
Note: By turning on Solo for both AUDIO 1 and AUDIO
2, you are specifying that only these audio tracks will be
heard and recorded.
2. In the P8: Insert Effect– Audio Routing 1 page, set up
both audio tracks 1 and 2 as shown below:
Bus Select (IFX/Indiv. Out Assign): L/R
Send 1 (MFX1) and Send 2 (MFX2): 000
Note: If you want to apply insert effects to the audio
tracks, set Bus Sel. (IFX/Indiv. Out Assign) to your
choice of IFX1–IFX12. Then choose L/R for the Bus
Select setting (P8: Insert Effect– Insert FX page) that
follows the insert effect you’re using.
Note: If you want to apply master effects to an audio
track, use “Send 1 (MFX1)” and “Send 2 (MFX2)” to
adjust the send levels to the master effects. If you are
using an insert effect on the audio track, adjust the Send1
and Send2 that follow the insert effect you’re using.
3. Press the SEQUENCER START/STOP switch to play
back the song, and adjust the balance of the audio
track 1 and 2 output levels.
The output level of each audio track is adjusted in the P0:
Play/REC Audio Track Mixer page by the audio track 1
and audio track 2 Vol ume setting.
When you’ve finished making adjustments, stop
playback.
4. In the P0: Play/REC– Preference page, use “Track
Select” to select Audio Track 03.
5. In Recording Setup, Recording Setup (Audio Track),
specify the desired recording method.
– Recording Setup –
Overwrite: on
– Recording Setup (Audio Track) –
Automation Only: unchecked
Source Direct Solo: unchecked
Auto Input: checked
Rehearsal: unchecked
– Audio TRK 03 –
Name, Take, Tak e N o . : Specify the desired region and
WAVE filename to be recorded.
Note: The settings up to this poin
t are the same as if you
used the page menu command Auto HDR/Sampling
Setup to execute Bounce Audio Track with the following
settings. For more information, see “Bounce Audio
Track” on page 634 of the Parameter Guide.
Mode: Mono
From: Audio Track 01: checked
Audio Track 02: checked
To: Audio Track 03
6. In the P0: Play/REC– Audio Track Mixer page, set
REC Source so that L will be recorded on audio track
3.
Audio track 3 REC Source: L
When bounce-recording audio tracks, turn the
metronome off (Metronome Setup “Sound”: Off).
Record
7. Set “Location” to the beginning of the song (001:
01.000).
8. Press the SEQUENCER REC/WRITE switch.
You will be in record-ready mode.
9. Press the SEQUENCER START/STOP switch.
Playback will begin, and bounce-recording will also
begin simultaneously.
When the audio tracks have finished playing back,
recording will also end. Song playback will also end
automatically.
Listen to the recorded result
10.In the P0: Play/REC– Audio TRACK Mixer page,
mute the playback of both audio tracks 1 and 2.
Play/Rec/Mute: Mute
Solo On/Off: Off
11.Press the SEQUENCER START/STOP switch to play
back the song.
Make output settings for audio track 3 as described in
“Listen to the recorded result” on page 102.
12.Press the SEQUENCER START/STOP switch to stop
playback.
If you want to create a WAVE file on the disk from a song
that includes audio tracks, see “Resampling a song to
create a Wave file” on page 160.