User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Creating songs (Sequencer mode)
104
Setup
1. In the P0: Play/REC– Preference page, make sure that
Audio Track 01 is selected for the “Track Select”
parameter.
2. Use Recording Setup to specify how recording will
start.
In this example, choose punch-in recording.
Auto Punch In: on
M***–M***: Specify the range of measures for which
you want to record.
AUDIO TRK 01 Name, Take, Take No.: Specify the
region and wave file name that you want to record.
Note: If you set Recording Setup to Auto Punch In and
set “M***–M***” to the desired range of measures,
playback will occur until that range of measures, and then
only the specified range of measures will be recorded.
If you set Recording Setup to Manual Punch In, the
measures you specify by pressing the SEQUENCER
REC/WRITE switch or foot switch will be recorded. In
this case, press the SEQUENCER START/STOP switch
to play back the song. When you reach the measure at
which you want to start recording, press the
SEQUENCER REC/WRITE switch or the foot switch to
begin recording. When you reach the measure at which
you want to stop recording, press the REC/WRITE
switch or foot switch once again; recording will end.
Rehearse
If desired, you can simulate the action of recording without
actually recording. This will function just as if you were
recording, but no audio event, region, or WAVE file will be
created.
3. In “Recording Setup (Audio Track),” check the
“Rehearsal” option.
4. Use “Location” to specify the location at which you
want to start recording. Set this several measures
earlier than the region you specified for “M***–
M***”.
5. Press the SEQUENCER REC/WRITE switch.
You will enter record-ready mode.
Once you press the SEQUENCER REC/WRITE switch,
you will be unable to change the audio track selection in
“Track Select.”
6. Press the SEQUENCER START/STOP switch.
Playback will begin from the measure specified by
“Location,” and simulated recording will occur only in
the range of measures specified by “M***-M***”. Then
playback will resume, and will continue to the end of the
song.
Note: If the “Recording Setup (Audio Track)” parameter
“Auto Input” is Off, you will always be able to hear the
REC Source. For more information, see “Auto Input” on
page 531 of the Parameter Guide.
7. Press the SEQUENCER START/STOP switch to stop
recording.
8. In “Recording Setup (Audio Track),” uncheck the
“Rehearsal” option.
Record
9. Use “Location” to specify the location at which you
want to start recording. Set this several measures
earlier than the region you specified for “M***–
M***”.
10.Press the SEQUENCER REC/WRITE switch.
You will enter record-ready mode.
Once you press the SEQUENCER REC/WRITE switch,
you will be unable to change the audio track selection in
“Track Select.”
11.Press the SEQUENCER START/STOP switch.
Playback will begin from the measure specified by
“Location,” and recording will occur only in the range of
measures specified by “M***–M***”. Then playback
will resume, and will continue to the end of the song.
Note: If the “Recording Setup (Audio Track)” parameter
“Auto Input” is Off, you will always be able to hear the
REC Source.
12.Press the SEQUENCER START/STOP switch to stop
recording.
Listen to the recorded result
13.Press the SEQUENCER START/STOP switch to play
back the song.
Make output settings for the audio track as described
under “Listen to the recorded result” on page 102.
14.Press the SEQUENCER START/STOP switch to stop
playback.
Compare the recorded result
• Press the COMPARE switch (the COMPARE switch
LED will light), and play back.
The audio track prior to punch-in recording will play
back.
• Once again press the COMPARE switch (the
COMPARE LED will go dark), and play back.
The audio track following punch-in recording will play
back.