User Manual
Table Of Contents
- About this manual
- Contents
- Introduction to KRONOS
- Front and rear panels
- Front panel
- 1. MAIN VOLUME knob
- 2. Control Surface
- 3. Data entry
- 4. DISK access indicator
- 5. MODE buttons
- 6. UTILITY buttons
- 7. BANK SELECT buttons
- 8. KARMA buttons
- 9. Vector Joystick
- 10. Drum Track
- 11. SW1 and SW2
- 12. Joystick
- 13. Ribbon controller
- 14. Headphone jack
- 15. EXIT button
- 16. SEQUENCER buttons
- 17. TEMPO controls
- 18. SAMPLING buttons
- 19. TouchView display
- Rear panel
- TouchView user interface
- Front panel
- Basic information
- Setup
- Update information
- Front and rear panels
- Playing and editing Programs
- Playing and editing Combinations
- Playing Combinations
- Easy Combination editing
- Detailed Combination editing
- Creating songs (Sequencer mode)
- Set Lists
- Sampling (Open Sampling System)
- Global Settings, Wave Seq., Drum Kits
- Loading & saving data, and creating CDs
- Using Effects
- Using KARMA
- Using the Drum Track
- Appendices
- Troubleshooting
- Error and confirmation messages
- A (ADC–Are You Sure)
- B (Buffer)
- C (Can’t calibrate–Completed)
- D (Destination–Disk)
- E (Error–Exceeded)
- F (File–Front)
- H
- I (Illegal–Index)
- K
- M (Master–Multisample)
- N (No data–Not enough song memory)
- O (Obey copyright rules–Oscillator)
- P (Pattern–Program)
- R (Rear sample–Root)
- S (Sample–Source)
- T (The clock–/TEMP folder detected)
- U (Unable to create directory–USB Hub)
- W (Wave)
- Y (You)
- Disk and Media information
- Specifications
- MIDI Implementation Chart
Audio recording Recording procedure
103
2. Set Track Select to Audio Track 02.
3. Record as described in step 8 and following of the
preceding section.
Applying an insert effect while you
record
In this example, we’ll apply an insert effect to the guitar
that’s connected to Audio Input 1, and record the effect-
processed sound on audio track 1.
Connect your guitar
1. Connect your guitar.
For detailed instructions, see “Recording an external input
on audio track 1” on page 100.
Setup
2. In the P0: Play/REC– Audio Input/Sampling page, set
the “Audio Input” parameters as shown below that
the signal from the AUDIO INPUT 1 jack is sent to
IFX1.
Use Global Setting: Off
Bus Select (IFX/Indiv.): IFX1
INPUT1 Level: 127
INPUT1 Pan: L000
INPUT1 REC Bus: Off
3. In the P8: Insert Effect– Insert FX page, select the
desired effect and route it to REC bus 1.
IFX1 On/Off: On
IFX1: the desired effect
Bus Sel.: Off
REC Bus: 1
4. In the P0: Play/REC– Audio Track Mixer page, set
REC Source to REC1 so that the signal of the REC
bus will be recorded on audio track 1.
Audio Track 1 REC Source: REC1
5. In the P0: Play/REC Preference page, set “Track
Select” to Audio Track 01.
The remaining steps are the same as step 3 and following
of the preceding section “Recording an external audio
source on audio track 1.” Please refer to that section for
details.
Punch-in recording an external input
source on an audio track
In this example, we’ll show how to punch-in record a portion
of the track you recorded in “Recording an external input on
audio track 1.”
Don’t change the P0: Play/REC– Audio Input/ Sampling
page “Audio Input” settings, the P0: Play/ REC– Preference
page “Recording Setup (Audio Track)” settings, or the “P0:
Play/REC– Audio Track Mixer page REC Source settings.
We will use these settings as they are.