User Manual

Appendices
268
The Touch Panel Calibration page will appear. Follow the
on-screen instructions to re-calibrate the touch panel.
Can’t switch modes or pages
If the KRONOS is doing any of the following, you may not
be able to change modes or switch to a different page:
• Recording or playing back a song or pattern
• Sampling (if the Sampling REC button is lit)
• Playing a CD on a connected USB CD drive
• Playing a WAVE file
• A menu dialog or select dialog is on the LCD display
In Combination or Sequencer modes, can’t edit
the value of Timbre/Track parameters such as
MIDI Channel or Status
Some parameters can’t be edited while notes are playing,
either locally or from MIDI. If the damper pedal is held
down, or if its calibration is incorrect, notes may be
sustaining even if they aren’t audible.
• Are you using a damper pedal with a polarity that does
not match the Damper Polarity setting (Global P2:
Controllers/Scales)? For more information, see “Damper
Polarity,” on page 792 of the Parameter Guide.
• In some cases, this problem can be solved be executing
the page menu command Half Damper Calibration
(Global P0: Basic Setup). For more information, see
“Half Damper Calibration,” on page 817 of the
Parameter Guide.
No beep sounds when you touch the LCD screen
Check the Beep Enable check box (Global P0: Basic Setup).
For more information, see “Sounding a beep when you press
the LCD screen” on page 177.
Audio input and output
No sound
Are connections made correctly to your amp, mixer, or
headphones? For more information, see “Connections” on
page 21.
Is the connected amp or mixer powered-on, and is its volume
raised?
Is Local Control turned on?
• In Global P1: MIDI, check the Local Control On check
box.
Is the MAIN VOLUME knob raised? See “MAIN
VOLUME knob” on page 1.
Is the MASTER slider raised? (See “Master Volume” on
page 29 of the Parameter Guide.)
Could MASTER VOLUME have been assigned to the
ASSIGNABLE PEDAL, and the pedal set in the minimum
position?
Could the vector joystick be controlling the volume?
• Try moving the vector joystick as you play.
If there is no sound from the AUDIO OUTPUT
(INDIVIDUAL) 1–4 jacks, make sure that Bus Select or
Bus Sel. (Bus Select) following the insert effect is set to 1–4,
or 1/2–3/4.
Does the “Samples Not Loaded” message appear? If so, is
the required sample data loaded?
If a specific timbre doesn’t sound in Combination mode, is
its Play/Mute button set to Play? Alternatively, are all Solo
settings turned off? (If the Solo button is blinking, this
means that at least one timbre is being soloed.)
If a specific track doesn’t sound in Sequencer mode, is its
Play/Rec/Mute button set to Play? Alternatively, are all Solo
settings turned off? (If the Solo button is blinking, this
means that at least one track is being soloed.)
Make sure that the Status is INT or BTH. (See “Preparations
for recording” on page 90.)
Are the Key Zone and Velocity Zone set so that sound will
be produced when you play?
Is the Global System Clock set to S/P DIF? If this is the
case, and a valid 48kHz S/P DIF source is not connected,
then the KRONOS outputs will be silent.
Can’t output sound from an audio CD
Make sure that you have selected the Disk mode Play Audio
CD page or Sampling mode.
Is the output of the audio CD being input correctly?
• In the Disk mode Play Audio CD Page, make the
appropriate settings for Bus Select (IFX/Indiv.) and
Level. Alternatively, in the Sampling mode P5: Audio
CD– Ripping page, make the appropriate settings for
Bus Select (IFX/Indiv.) and Level.
•Is the Drive Select setting correct?
Is the MAIN VOLUME knob raised?
If you created the CD using the KRONOS, has the CD been
finalized?
• A CD-R/RW disc created using the Disk mode Make
Audio CD page cannot be played until you also finalize
the disc. Use the page menu command Finalize Audio
CD to finalize the disc. For more information, see
“Finalize Audio CD” on page 867 of the Parameter
Guide.
Audio inputs don’t work properly
Are the appropriate sources connected to the analog,
S/P DIF, or USB inputs?
If there is no sound in Sampling mode, check that Bus Select
(IFX/Indiv.), and Level are set correctly in the Sampling P0:
Recording– Audio Input page.
Alternatively, is SAMPLING REC turned on?