User's Manual
Table Of Contents
- Table of Contents
- Introduction
- Quick Start
- Turning the power on/off
- Listening to the demo songs
- Selecting and playing a program
- Selecting and playing a combination
- Using controllers to modify the sound
- Using the arpeggiator while you play
- Playing with the RPPR (Realtime Pattern Play/Recording) function
- Simple program editing
- Simple combination editing
- Sampling (recording a sample)
- Basic functions
- Saving data
- Restoring the factory settings
- Program mode
- How a program is organized
- Basic program editing
- Oscillator settings 2.1: Ed–Basic
- Controller settings 2.2: Ed–Ctrl
- Pitch settings 3.1: Ed–Pitch
- Filter settings 4.1: Ed–Filter1, 4.2: Ed–Filter2
- Amplifier settings 5.1: Ed–Amp1, 5.2: Ed–Amp2
- LFO settings 5.3: Ed–LFOs
- Arpeggiator settings 6.1: Ed–Arp.
- BUS settings 7.1: Ed–InsertFX BUS
- Insert Effect settings 7.1: Ed–InsertFX Setup, IFX
- Master Effect settings 7.2: Ed–MasterFX
- More about Alternate Modulation
- Auto Song Setup function
- Combination mode
- How a combination is organized
- Basic combination editing
- Timbre 1–8 program, pan and volume 2.1: Ed–Prog/Mix
- Controller settings 2.2: Ed–Ctrl
- Settings for status, MIDI channel, and playing mode 3.1: Ed–Param1
- Note timing and scale settings 3.2: Ed–Param2
- Layer and split settings 3.3: Ed–Key Zone
- Velocity switch settings 3.4: Ed–Vel Zone
- MIDI filter settings 4.1: Ed–MIDI Filter1–4.4: Ed–MIDI Filter4
- Arpeggiator settings 6.1: Ed–Arp.
- Bus settings 7.1: Ed–InsertFX BUS
- Insert Effect settings 7.1: Ed–InsertFX Setup, IFX
- Master Effect settings 7.2: Ed–MasterFX
- Auto Song Setup function
- How a combination is organized
- Sequencer mode
- Sampling mode
- Global mode
- Media mode
- Arpeggiator settings
- Effects settings
- Other functions
- Tuning to another instrument/ Transposing
- Bypassing the effects
- Specifying the function of the Assignable Switch and Assignable Pedal
- Selecting different Velocity and Aftertouch curves
- Creating original scales
- Changing the scale
- Setting the function of [SW1] and [SW2]
- Setting the B-mode functions of REALTIME CONTROLS [1]–[4]
- Adjusting the contrast (brightness) of the LCD screen
- Using this instrument as a data filer
- Tap tempo control
- Shortcuts
- Appendices
85
Basic functions
Sequencer mode
Control data in pattern recording
To record control data in a pattern, you should
restore the control data to its normal value within
the pattern. If you fail to restore the normal value,
unnecessary control data may remain in a “stuck”
position when you place the pattern in a song or
use the RPPR function to play the pattern. How-
ever, the following control data will be automati-
cally reset to the following values when the song
or RPPR function finishes playing the pattern, or
when playback is halted.
Controller Reset value
Modulation 1 (CC#01) 00 (zero)
Modulation 2 (CC#02) 00 (zero)
Expression (CC#11) 127 (max)
Ribbon controller (CC#16) 64 (center)
Damper switch (CC#64) 00 (zero)
Sostenuto switch (CC#66) 00 (zero)
Soft switch (CC#67) 00 (zero)
EG sustain level (CC#70) 64 (center)
Resonance level (CC#71) 64 (center)
EG release time (CC#72) 64 (center)
EG attack time (CC#73) 64 (center)
Low pass filter cutoff (CC#74) 64 (center)
EG decay time (CC#75) 64 (center)
LFO1 speed (CC#76) 64 (center)
LFO1 depth (pitch) (CC#77) 64 (center)
LFO1 delay (CC#78) 64 (center)
Filter EG intensity (CC#79) 64 (center)
SW1 modulation (CC#80) 00 (zero)
SW2 modulation (CC#81) 00 (zero)
Channel after touch 00 (zero)
Pitch bender 00 (zero)