User's Manual
Table Of Contents
- Table of Contents
- Introduction
- Quick Start
- Turning the power on/off
- Listening to the demo songs
- Selecting and playing a program
- Selecting and playing a combination
- Using controllers to modify the sound
- Using the arpeggiator while you play
- Playing with the RPPR (Realtime Pattern Play/Recording) function
- Simple program editing
- Simple combination editing
- Sampling (recording a sample)
- Basic functions
- Saving data
- Restoring the factory settings
- Program mode
- How a program is organized
- Basic program editing
- Oscillator settings 2.1: Ed–Basic
- Controller settings 2.2: Ed–Ctrl
- Pitch settings 3.1: Ed–Pitch
- Filter settings 4.1: Ed–Filter1, 4.2: Ed–Filter2
- Amplifier settings 5.1: Ed–Amp1, 5.2: Ed–Amp2
- LFO settings 5.3: Ed–LFOs
- Arpeggiator settings 6.1: Ed–Arp.
- BUS settings 7.1: Ed–InsertFX BUS
- Insert Effect settings 7.1: Ed–InsertFX Setup, IFX
- Master Effect settings 7.2: Ed–MasterFX
- More about Alternate Modulation
- Auto Song Setup function
- Combination mode
- How a combination is organized
- Basic combination editing
- Timbre 1–8 program, pan and volume 2.1: Ed–Prog/Mix
- Controller settings 2.2: Ed–Ctrl
- Settings for status, MIDI channel, and playing mode 3.1: Ed–Param1
- Note timing and scale settings 3.2: Ed–Param2
- Layer and split settings 3.3: Ed–Key Zone
- Velocity switch settings 3.4: Ed–Vel Zone
- MIDI filter settings 4.1: Ed–MIDI Filter1–4.4: Ed–MIDI Filter4
- Arpeggiator settings 6.1: Ed–Arp.
- Bus settings 7.1: Ed–InsertFX BUS
- Insert Effect settings 7.1: Ed–InsertFX Setup, IFX
- Master Effect settings 7.2: Ed–MasterFX
- Auto Song Setup function
- How a combination is organized
- Sequencer mode
- Sampling mode
- Global mode
- Media mode
- Arpeggiator settings
- Effects settings
- Other functions
- Tuning to another instrument/ Transposing
- Bypassing the effects
- Specifying the function of the Assignable Switch and Assignable Pedal
- Selecting different Velocity and Aftertouch curves
- Creating original scales
- Changing the scale
- Setting the function of [SW1] and [SW2]
- Setting the B-mode functions of REALTIME CONTROLS [1]–[4]
- Adjusting the contrast (brightness) of the LCD screen
- Using this instrument as a data filer
- Tap tempo control
- Shortcuts
- Appendices
56
More about Alternate Modulation
Alternate Modulation is a type of modulation that can
be used to control various aspects of the sound.
AMS (Alternate Modulation Source) refers to any of
the numerous sources that can control alternate modu-
lation, and includes controllers that you operate physi-
cally such as the joystick and realtime controllers,
incoming MIDI data, as well as modulators such as the
EG or LFO.
Since this instrument allows you apply modulation to
a modulator, this type of control is referred to as “alter-
nate modulation.”
Intensity is a parameter that sets the degree (speed or
depth) to which AMS will control alternate modula-
tion.
Combinations of modulations that are frequently used
in on the synthesizer. performance (such as using the
joystick to vary the pitch) are also provided as special
parameters separately from alternate modulation.
This instrument provides 29 types of alternate modula-
tion.
In single mode you can use 29 alternate modulation
destinations of 29 types, and in double mode you can
use 55 alternate modulation destinations of 29 types.
There are 42 AMS sources. (However depending on the
type of modulation, some sources cannot be selected.)
For details on alternate modulation and AMS, refer to
PG p.215.
Suggestions on using alternate modulation
When making settings for alternate modulation, think
of the effect that you wish to produce, what type of
modulation will be necessary to produce that effect,
and what parameter of the oscillator, filter, or amplifier
needs to be controlled. Then select a source (“AMS”)
and set the “Intensity.” If you proceed logically in this
way, you will achieve the desired effect.
For example if you want to “control a guitar-like sound
so that it appears to be approaching feedback when the
joystick is moved away,” you will make settings so that
the joystick controls filter modulation or the resonance
level.
Auto Song Setup function
This function automatically applies the settings of the
current program or combination to a new song in the
sequencer.
If inspiration for a phrase or song strikes you while
you’re playing a program or combination, you can use
this function to start recording immediately.
Hold down the [ENTER] key and press the
SEQUENCER [REC/WRITE] key. The “Setup to
Record” dialog box will open and ask “Are you sure?”.
Press [F8] (“OK”) key. You will automatically enter
Sequencer mode, and will be in the record-ready state.
Press the [START/STOP] key to start the sequencer
and begin recording.