User's Manual
Table Of Contents
- Table of Contents
- Introduction
- Quick Start
- Turning the power on/off
- Listening to the demo songs
- Selecting and playing a program
- Selecting and playing a combination
- Using controllers to modify the sound
- Using the arpeggiator while you play
- Playing with the RPPR (Realtime Pattern Play/Recording) function
- Simple program editing
- Simple combination editing
- Sampling (recording a sample)
- Basic functions
- Saving data
- Restoring the factory settings
- Program mode
- How a program is organized
- Basic program editing
- Oscillator settings 2.1: Ed–Basic
- Controller settings 2.2: Ed–Ctrl
- Pitch settings 3.1: Ed–Pitch
- Filter settings 4.1: Ed–Filter1, 4.2: Ed–Filter2
- Amplifier settings 5.1: Ed–Amp1, 5.2: Ed–Amp2
- LFO settings 5.3: Ed–LFOs
- Arpeggiator settings 6.1: Ed–Arp.
- BUS settings 7.1: Ed–InsertFX BUS
- Insert Effect settings 7.1: Ed–InsertFX Setup, IFX
- Master Effect settings 7.2: Ed–MasterFX
- More about Alternate Modulation
- Auto Song Setup function
- Combination mode
- How a combination is organized
- Basic combination editing
- Timbre 1–8 program, pan and volume 2.1: Ed–Prog/Mix
- Controller settings 2.2: Ed–Ctrl
- Settings for status, MIDI channel, and playing mode 3.1: Ed–Param1
- Note timing and scale settings 3.2: Ed–Param2
- Layer and split settings 3.3: Ed–Key Zone
- Velocity switch settings 3.4: Ed–Vel Zone
- MIDI filter settings 4.1: Ed–MIDI Filter1–4.4: Ed–MIDI Filter4
- Arpeggiator settings 6.1: Ed–Arp.
- Bus settings 7.1: Ed–InsertFX BUS
- Insert Effect settings 7.1: Ed–InsertFX Setup, IFX
- Master Effect settings 7.2: Ed–MasterFX
- Auto Song Setup function
- How a combination is organized
- Sequencer mode
- Sampling mode
- Global mode
- Media mode
- Arpeggiator settings
- Effects settings
- Other functions
- Tuning to another instrument/ Transposing
- Bypassing the effects
- Specifying the function of the Assignable Switch and Assignable Pedal
- Selecting different Velocity and Aftertouch curves
- Creating original scales
- Changing the scale
- Setting the function of [SW1] and [SW2]
- Setting the B-mode functions of REALTIME CONTROLS [1]–[4]
- Adjusting the contrast (brightness) of the LCD screen
- Using this instrument as a data filer
- Tap tempo control
- Shortcuts
- Appendices
5
Introduction
Front and rear panel
Front and rear panel
Front panel
1. [SW1] key, [SW2] key
These keys are on/off switches for the functions to
which they were assigned in Program, Combination,
Sequencer and Sampling modes (if the EXB-SMPL
option is installed). When on, the key will light
(
☞p.24).
2. Joystick
This controls pitch or modulation, etc.
Move the joystick up/down or left/right (+Y, –Y,
–X, +X) to control (
☞p.24).
Various program parameters and effect parameters
will determine what is controlled by the joystick.
3. Headphone jack
A set of headphones with a (1/4") stereo phone plug
can be connected here.
The output from the L/MONO and R OUTPUT jacks
can be monitored in stereo through the headphones.
4. [VOLUME] slider
This adjusts the volume that is output from the OUT-
PUT jacks (L/MONO, R) and the headphone jack.
5. REALTIME CONTROLS
Use the [SELECT] key to select realtime controller
mode A/B/C, and use knobs [1]–[4] to control the
tone, effects, MIDI control changes, and arpeggiator
etc. while you perform. (
☞p.25, 27)
[SELECT] key
This key switches the realtime controller between A-
mode, B-mode, and C-mode. The LED of the selected
mode will light.
[ARP ON/OFF] key
This key turns the arpeggiator on/off. When on, the
key will light.
[1], [2], [3], [4] knob
A-mode
[1] LPF CUTOFF:
Controls the cutoff frequency of the low pass filter.
[2] RESONANCE/HPF:
Controls the filter resonance level or the high pass filter
cutoff frequency.
1
3
4
7
9
10
13
12
2
5
68
11