Test Report No.
Models KLT-1514A 420-0881 REV.
TABLE OF CONTENTS HOW TO REACH RADIUS If you have any questions or need assistance regarding your monitor, you may contact KDS directly using any of the following methods: TECHNICAL SUPPORT Toll Free 800-283-1311 WEBSITE www.kdsusa.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.
SAFETY INSTRUCTIONS DDC COMPLIANCE NOTICE: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. ■ Handling Due to its fragile glass panel, this monitor must be handled with caution and not be exposed to impact or shock. Never touch the display area or rub it with a hard object or tool, as the panel is easily scratched.
■ Caution 1. Do not open any covers on the monitor. No user serviceable parts are inside. 2. In an emergency, disconnect the AC power plug. 3. To avoid electrical shock, disconnect the power cord from the monitor before connecting the signal cable to the computer. 4. Keep away from liquids and flame. Do not immerse this monitor in water or any other liquid. Do not use this device in excessively hot conditions. 5. Handle the power cord with care.
MONITOR FEATURES Before operating your display, please check to make sure that all of the items listed are present in your package: * Supports Analog IBM compatible PC, Apple MacintoshTM (Adapter optional) * Supports DPMS for monitor power management 1) Color TFT LCD Monitor (With 15-pin D-SUB cable) * Support DDC2B 2) Power Card * On Screen Control : Auto-Tune, Contrast, Brightness, H/V Position, HSize, Phase, Auto-Level, Color Control, OSD Position, OSD Time-out, Power Save Delay, Language, Informat
INSTALLATION CONTROL BUTTONS ◆ Follow these steps to install the monitor GETTING GETTING STARTED STARTED GETTING STARTED STARTED GETTING 1. Before you connect the cables, make sure the monitor and system unit power switches are OFF. 2. Plug one end of the 15-pin signal cable to the rear of your system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3.
ON-SCREEN DISPLAY AUTO MENU DESCRIPTIONS GETTING STARTED STARTED GETTING This LCD monitor features an On-Screen Display (OSD) menu. These icons are designed to make your monitor display settings easier to control. When highlighted, the icons illustrate Rthe control function to assist you in identifying which control needs adjustment. ON SCREEN CONTROL AUTO AUTOAUTO The OSD menu activates R automatically when you press the Enter button R Rcentered on the screen on the rear of the monitor.
AUTO R AUTO AUTO AUTO TROUBLESHOOTING R RR PHASE POWER SAVE DELAY Select this controlAUTOand then use the and AUTO AUTO image until it looks focused, crisp and sharp. buttons to adjust the screen AUTO AUTO AUTO-LEVEL R COLOR CONTROL RR AUTO AUTO AUTO Select this control, then use the and buttons to scroll to the desired color temperature. UseAUTOthe button to select the 9300K, 6500K, 5500K R or USER for custom setting.
POWER MANAGEMENT TIMING GUIDE LED INDICATOR (POWER MANAGEMENT ACTIVE) The LCD is a multi-frequency display. It operates at horizontal frequencies between 30KHz ~ 60KHz and vertical frequencies between 55Hz ~ 75Hz. Because of its microprocessor-based design, it offers autosynchronization and auto-sizing capabilities. This monitor offers 8 preprogrammed settings that are listed in the timing table on page 11.
PIN ASSIGNMENT VGA Connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 VGA CONNECTOR Red Green Blue No Connection Ground Red Ground Green Ground Blue Ground No Connection Ground Ground DDC SDA Horizontal Sync. Vertical Sync. DDC SCL LCD Color Filter Colors Glass surface 15” diagonal viewable screen TFT (Thin Film Transistor), Active Matrix Panel, 0.297mm pixel pitch R,G,B vertical stripe 16M Anti-glare coating Left / Right Up / Down 70 / 70 55 / 60 Contrast Ratio Typ.
TROUBLESHOOTING ◆ No power. ✓ Flip the power switch ON. The Power LED turns on. ✓ Make sure AC power cord is securely connected to a power outlet. ◆ Power on but no screen image. ✓ Make sure the video cable attached with this monitor is tightly secured to the video output port on the back of the computer. ✓ Adjust the brightness and contrast. ◆ Image is unstable, unfocused. ✓ Use “AUTO-TUNE” to adjust automatically.
MEMO MEMO
