Owners Manual
OPERATING INSTRUCTIONS (cont.)
TEMPERATURE SETTING
• Set the desired cooling temperature by pressing the ‘UP’ or ‘DOWN’ key to set your desired
temperature. Each depression of the buttons will scroll through the available temperature
settings in increments of 1 degree.
MEMORY FUNCTION
• The cooler has the power off memory function. When power on again, the wine cooler will
operate according to the setting mode before power off.
• For sparkling wine the temperature should be set between 46°- 48°F (8°- 9°C)
• For white wine the temperature should be set between 48°- 54°F (9°- 12°C)
• For red wine the temperature should be set between 55°- 65°F (13°- 18°C)
NOTES
• If the unit is unplugged, power loss, or turned off, you must wait 3 to 5 minutes before
restarting. If you attempt to restart before this interval the Wine Cooler will not start.
• When you use the wine cooler for the first time or restarting after being shut off for a long
time, there could be a few degrees variance between the temperature you select and the
one indicated on the LED readout. This is normal and it is due to the length of the activa-
tion time. Once the wine cooler is running for a few hours everything will return to normal.
• The zone temperature may have a difference of +/- 5°F (+/- 3°C) from setting depending
on loading and ambient conditions.
WARNING
Be careful when using the touch screen panel. Please protect the panel carefully to avoid
scratches, and maintain far away from strong magnetic field and high humidity areas, these
conditions may prevent the wine cooler from working properly.
FAULT INDICATION
• If the indication of the following table is displayed on the display area, it means the cooler
is with faults.
FAULT CODE FAULT DESCRIPTION
upper chamber display E1 Failure of temperature sensor in upper chamber
lower chamber display E1 Failure of temperature sensor in lower chamber
upper chamber display E4 Failure of defrosting sensor in upper chamber
lower chamber display E4 Failure of defrosting sensor in lower chamber
upper chamber display E6 Communication fault
WARNING When the above faults are displayed on the screen, please do not disassemble to check
by yourself. Please contact the special maintenance personnel of the local after-sales service
company for the maintenance.
5
OPERATING INSTRUCTIONS
• Powering on first time, the display screen gives a full display for 3s and the start-up sound
rings; then the machine enters into operation in the locked state.
• The setting temperatures of both zones will be displayed.
LOCK/UNLOCK KEY
- By pressing the ‘LOCK’ button for 3s in the locked mode, the buzzer sounds and the
unlocked mode is activated; After unlocking, the temperature display area of selected
chamber flashes.
- By pressing the ‘LOCK’ button for 3s in the unlocked mode, the buzzer rings and the
locked mode is activated; the temperature display areas of upper and lower chambers
stop flashing.
• In unlocked state, if the control panel is not touched within 30 seconds, the display screen
will stop flashing. When the cooler is in locked state, after 30 seconds, the display screen
will turn off. The display screen will turn on again when touching any key.
• In the locked mode, if touching any key besides ‘LIGHT’, the display screen will keep
flashing for 2.5s and the buzzer will alert to unlock the unit.
LIGHT key
• The light turns on by default for 30s. If the ‘LIGHT’ key is not operated within 30s, the light
will automatically turn off.
• Press the ‘LIGHT’ key to turn the light on or off.
SWITCH BETWEEN FAHRENHEIT AND CELSIUS TEMPERATURE DISPLAY
• In unlocked mode, press the UP key DOWN key at the same time for 3s to finish the switch
between Celsius temperature and Fahrenheit temperature; the screen will display the
Fahrenheit temperature or Celsius temperature under the current mode.
ZONE SELECTION
• Powering on first time, the temperature of each chamber will be set according to default
setting. By pressing the ‘ZONE SELECTION’ key, the temperature area will be switched
between upper chamber and lower chamber. Once a chamber is selected, the display will
flash and at this time the temperature of that chamber can be set up.
4
LIGHT TEMP.
UP
ZONE
SELECTION
LOCK UPPER
ZONE
LOWER
ZONE
TEMP.
DOWN