Full Product Manual

折页 尺寸：100mm*120mm
QUICK START GUIDE
1. Plug the Smart Plug into a desired outlet. The LED will start blinking green to indicate it is ready for network
setup.
2. Make sure your iPhone or iPad (iOS 8.1 or later) is connected to a 2.4GHz Wi-Fi network. Using the router
utility software, shutdown 5GHz Wi-Fi networks.
3. Download and open the free Koogeek Home app from the App Store.
4. Log in or sign up for a Koogeek account or simply tap Skip.
5. Tap “+” on the top right corner and follow the on-screen directions to complete network setup.
Note: To add more plugs (or repeat the plug setup process), tap “+” and you will see the accessory list. Each
accessory has an identification code, e.g., Koogeek-XX-XXXXXX. Make sure the last 6 characters of the
identification code is consistent with the last 6 characters of MAC on the back of your Smart Plug.
6. When prompted, scan the setup code or manually enter the setup code, and then follow the step to add the
device to the Home and Room.
After scanning the setup code, if the app prompts “Couldn’t add Koogeek-XX-XXXXXX”, please refer to the first
FAQ. Please keep the setup code for future use.
7. You can assign a name to your device and use this name when speaking to Siri. For example, you can name
your device “Printer”, then launch Siri and speak “Turn on the Printer”.
8. Set up customized scenes to control multiple devices with a single command. For example, if you assign the
“I'm going to bed” command to the scene of turning off bedroom light and turning on the fan, when you
speak “I'm going to bed” to Siri, everything is done.
9. For troubleshooting visit www.koogeek.com
Note:
The use of a HomeKit-enabled accessory need the follow permissions:
Settings > iCloud > iCloud Drive > Turn On
Settings > iCloud > Keychain > Turn On
Settings > Privacy > HomeKit > Koogeek Home > Turn On
QUICK START GUIDE
P1
SMART
PLUG
1
2
Legal
Use of the Works with Apple HomeKit logo
means that an electronic accessory has
been designed to connect specifically to
iPod touch, iPhone, or iPad, respectively, and
has been certified by the developer to meet
Apple performance standards. Apple is not
responsible for the operation of this device
or its compliance with safety and regulatory
standards.
Controlling this HomeKit-enabled accessory
automatically and away from home requires
an Apple TV with tvOS 10.1 or later or an iPad
with iOS 10.1 or later set up as a home hub.
Operation is Subject to the Following Two Conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the follow
two conditions: (1) This device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS(s). Son fonctionnement est
soumis aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer d'interférences et (2) cet appareil
doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.
www.koogeek.com
4
FAQ
Why did I fail to add my Smart Plug to the Koogeek Home app?
1. Make sure your accessory is powered on and nearby.
2. If you have a dual band router, please shutdown 5GHz Wi-Fi networks and connect your phone to the
2.4GHz Wi-Fi network.
3. Make sure your accessory’s green LED flashes slowly, if not, please press and hold the reset button for 10
seconds to restore factory settings.
4. Select the accessory shown on screen, then scan the setup code which can be found on the device,
instruction manual or inner packaging.
5. If the app prompts “Couldn’t add Koogeek –XX-XXXXXX” after you scanning the setup code:
(1) delete the current “Home” in Home Settings and close the app;
(2) restore the accessory to factory settings;
(3) add the accessory again.
Smart Plug works normally after restoring factory settings or unpluging/plugging, but it
occasionally gets disconnected from networks and can not be recognized
1. Make sure the number of Wi-Fi connected devices is within the wireless network capacity of your router.
Otherwise, please replace with another router.
2. Reconnect your iOS devices to Wi-Fi and make sure your Wi-Fi signal is strong enough.
3. Wait until the network is fixed if your router performs poorly in wireless networks that might result from
network congestion.
4. Check the router setting and see if there is any limit to the number of simultaneous client connections.
5. Restart your HomeKit accessory or restore your HomeKit accessory to factory settings, and add your
HomeKit accessory to the Koogeek Home app.
6. Update the firmware to the latest version.
How to automate and remotely access my HomeKit accessories?
1. Please visit www.koogeek.com/support/homekit.html
Follow Koogeek www.facebook.com/Koogeek
5
Press once to manually control the switch (Turning plug “On” or “Off”)
Restore factory setting: Press and hold the button for about 10 seconds until the LED turns
red. When the LED blinks green, it indicates you have restored the device to factory settings.
Electrical Ratings
120V AC, 60Hz
15A
1800W
General use
Safety Warnings
Plug directly into electric outlet (not into extension cord)
For indoor use only
Remove Smart Plug from outlet before cleaning
DO NOT clean with liquid
DO NOT remove ground pin (middle pin)
DO NOT use in wet or damp areas
Keep children away from Smart Plug and outlet
DO NOT exceed the recommended electrical ratings
DO NOT use in precision timing applications where inaccurate timing could be dangerous (sunlamps, saunas, etc.)
DO NOT use with devices that should not be operated unattended
· Flashing green: Smart Plug is waiting for a Wi-Fi network configuration
· Flashing red: Smart Plug is disconnected from a Wi-Fi network
· Solid green: Smart Plug is “On”
· Light off: Smart Plug is “Off”
Button Power / Wi-Fi Status Indicator
PLUG OVERVIEW
Button
Power / Wi-Fi Status Indicator (after setting up)
3