KT-PCIe-DVI-HDMI-I KT-PCIe-DVI-HDMI-I Users Guide KTD-N0800-0
KTD-N0800-0 Page 2 Document details Document revision history. Revision Date By 0 Mar. 1st 2010 JSE/MLA Comment Preliminary version Copyright Notice: Copyright © 2009, KONTRON Technology A/S, ALL RIGHTS RESERVED. No part of this document may be reproduced or transmitted in any form or by any means, electronically or mechanically, for any purpose, without the express written permission of KONTRON Technology A/S.
KTD-N0800-0 Page 3 Document details Life Support Policy KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON Technology A/S.
KTD-N0800-0 Page 4 » Table of Contents « Introduction .............................................................................................. 5 1 Mechanical Drawings........................................................................ 6 2 Functional Diagram........................................................................... 7 3 Jumpers ............................................................................................ 8 4 Connectors ........................................
KTD-N0800-0 Page 5 Introduction Introduction When the KT-PCIe-DVI-HDMI-I card is plugged into the PCI-Expressx16 connector then the motherboard automatically detects the card and select TMDS output. The card operates at pixel rates of up to 165MHz per link, supporting 1920x1200 panels at a 60Hz refresh rate. • • • • • • • • • • • • • • Low profile DVI/HDMI module (< 35mm above MB PCB) High-speed TMDS. Panel resolution up to 1920x1200 or similar. Support independent DVI and HDMI dual display.
KTD-N0800-0 Page 6 Mechanical Drawings Mechanical Drawings -1.0 0.0 (All measures in mm) 129.4 139.5 34.6 17.0 8.0 4.4 0.0 Motherboard PCB 79.2 120.0 0.
KTD-N0800-0 2 Page 7 Functional Diagram Functional Diagram 820977 KT-PCIe-DVI-HDMI-I DVI connector HDMI connector 5V Current limited supply Level Shifter TMDS0 Level Shifter DVI/TMDS configuration (Jumper settings) TMDS1 PCI-Expressx16 connector TMDS Motherboard with multiplexed PCI-Expressx16/SDVO/TMDS connector KT-PCIe-DVI-HDMI-I Users Guide
KTD-N0800-0 3 Page 8 Jumpers Jumpers Pin1 Jumper settings: Pin 1 DVI-SIL configured for DVI (Default) 3 4 J2-3 Pin 1 DVI-SIL configured for TMDS 2 2 2 6 J5-6 3 J1-2 Pin 1 5 4 5 7 4 5 9 10 11 12 J7-8 6 7 J4-5 3 8 8 9 10 11 12 J8-9 6 7 8 9 10 11 12 How to interface EEPROM (Used to program EDID for TMDS) CLK DAT KT-PCIe-DVI-HDMI-I Users Guide 3.
KTD-N0800-0 4 Page 9 Connectors Connectors HDMI connector The HDMI connector is of type Samtec HDMI-19-01-S-SM or similar.
KTD-N0800-0 5 Page 10 Cable Kit Cable Kit DVI Converter PCB is attached as a brake off module to the KT-PCIe module. The converter contains two connectors to convert from DVI-SIL (Hirose DF19L-20P-1H) to DVI-I. The KT-PCIe-modules includes DVI cable 300mm long (PN. 821524) in order to convert the SIL-DVI connector to a DVI-I connector. The cable wiring is a one-to-one connection. 1 9 17 The DVI-I connector is a Molex 74320-1004 (or similar). Only DVI Digital output is supported.
KTD-N0800-0 6 Page 11 Installation Guide Installation Guide These KT-PCIe cards fits into a standard PCIe connector like the Molex 877159308 PCIe edge connector which has no integrated PCIe card lock. The 820977 kit contains: 1. Cable 821524 2. Two Hex Nuts for the DVI connector to fix on a bracket 3. The 820877 module 4. Low Profile Brackets for HDMI 5. Low Profile Brackets for DVI 6. Full Height ATX Bracket for HDMI and DVI 7.
KTD-N0800-0 7 Page 12 Specifications Specifications Cable length: HDMI and DVI Cable length tested to 10 meters. Picture quality depends on display and cable, some combination might fail at high resolution (like 1600x1200) when cable length > 5 meters. Power consumption: The +5V available on both the HDMI and DVI can deliver minimum 0.5A even though only 55mA is required in according to DVI/HDMI standard. The +5V is protected by Resettable Fuse. 12V (via PCIe) 1.3W max. (0.55W externally and 0.
KTD-N0800-0 Page 13 Appendix EDID version 1.x. Descriptor structure defined in the VESA EDID code loaded in EEPROM, used for support of TMDS displays. Byte 1. 2. 3. 4. 5-Bit 7-4: 5-Bit 3-0: 6. 7. 8-Bit 7-4: 8-Bit 3-0: 9. 10. 11-Bit 7-4: 11-Bit 3-0: 12-Bit 7-6: 12-Bit 5-4: 12-Bit 3-2: 12-Bit 1-0: 13. 14.
