CP6003-SA 6U CompactPCI Processor Board based on the 2nd Generation Intel® Core™ i7/i5 Processor with the Intel® QM67 Express Chipset Doc. ID: 1044-9757, Rev. 2.0 September 15, 2011 If it’s embedded, it’s Kontron.
Preface CP6003-SA Revision History Publication Title: CP6003-SA: 6U CompactPCI Processor Board based on the 2nd Generation Intel® Core™ i7/i5 Processor with the Intel® QM67 Express Chipset Doc. ID: 1044-9757 PRELIMINARY Rev. Brief Description of Changes Date of Issue 1.0 Initial issue 22-Jul-2011 2.
CP6003-SA Preface Revision History .........................................................................................................ii Imprint ........................................................................................................................ii Disclaimer ..................................................................................................................ii Table of Contents ..........................................................................................
Preface 2. CP6003-SA Functional Description ............................................................ 2 - 3 2.1 Processor .................................................................................................2 - 3 2.2 Memory ....................................................................................................2 - 4 2.3 Intel® QM67 Express Chipset .................................................................2 - 4 2.4 Timer ...................................................
CP6003-SA Preface 2.10.11.3 Packet Switching Backplane (PICMG 2.16) ......................... 2 - 23 2.10.11.4 Hot Swap Support ................................................................ 2 - 23 2.10.11.5 Power Ramping .................................................................... 2 - 23 2.10.11.6 Precharge ............................................................................. 2 - 23 2.10.11.7 Handle Switch ...................................................................... 2 - 23 2.
Preface CP6003-SA 4.2 Jumper Description ..................................................................................4 - 5 4.2.1 COMB Termination Jumper Settings ...............................................4 - 5 4.3 I/O Address Map ......................................................................................4 - 6 PRELIMINARY 4.4 CP6003-SA-Specific Registers ................................................................4 - 7 4.4.1 Status Register 0 (STAT0) .........................
CP6003-SA 6. Preface Thermal Considerations ......................................................... 6 - 3 6.1 Board Internal Thermal Monitoring .......................................................... 6 - 3 6.2 Processor Thermal Monitoring ................................................................ 6 - 3 6.2.1 Digital Thermal Sensor (DTS) ......................................................... 6 - 3 6.2.2 Adaptive Thermal Monitor .............................................................
PRELIMINARY Preface CP6003-SA This page has been intentionally left blank. Page viii ID 1044-9757, Rev. 2.
CP6003-SA Preface 1-1 CP6003-SA Main Specifications .............................................................. 1 - 10 1-2 Standards ................................................................................................ 1 - 16 1-3 Related Publications ................................................................................ 1 - 17 2-1 Features of the Processors Supported on the CP6003-SA ....................... 2 - 4 3 IPMI and Hot Swap LEDs Function ..........................
Preface CP6003-SA 4-2 DIP Switch SW2 for CompactPCI Interface Configuration ......................... 4 - 4 4-3 DIP Switch SW3 for PMC Interface Configuration ..................................... 4 - 4 4-4 JP2 Jumper Setting for RS-422 TXD Termination (COMB) ....................... 4 - 5 4-5 JP3 Jumper Setting for RS-422 RXD Termination (COMB) ....................... 4 - 5 4-6 I/O Address Map ........................................................................................
CP6003-SA Preface 1-1 CP6003-SA Functional Block Diagram .................................................... 1 - 6 1-2 CP6003-SA Front Panel .......................................................................... 1 - 7 1-3 CP6003-SA Board Layout – Top View .................................................... 1 - 8 1-4 CP6003-SA Board Layout – Bottom View ............................................... 1 - 9 2-1 USB Connectors J6 and J7 .........................................................
PRELIMINARY Preface CP6003-SA This page has been intentionally left blank. Page xii ID 1044-9757, Rev. 2.
CP6003-SA Preface Proprietary Note This document contains information proprietary to Kontron. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents. The information contained in this document is, to the best of our knowledge, entirely correct.
Preface CP6003-SA Explanation of Symbols Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material. Please refer also to the section “High Voltage Safety Instructions” on the following page.
CP6003-SA Preface For Your Safety Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
Preface CP6003-SA General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
CP6003-SA Preface Two Year Warranty Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase. This warranty is not transferable nor extendible to cover any other users or long-term storage of the product. It does not cover products which have been modified, altered or repaired by any other party than Kontron or their authorized agents.
PRELIMINARY Preface CP6003-SA This page has been intentionally left blank. Page xviii ID 1044-9757, Rev. 2.
Introduction Chapter 1 Introduction ID 1044-9757, Rev. 2.
PRELIMINARY Introduction CP6003-SA This page has been intentionally left blank. Page 1 - 2 ID 1044-9757, Rev. 2.
CP6003-SA 1. Introduction 1.1 Board Overview Introduction The CP6003-SA (Standard Air-Cooled) is a highly integrated 6U CompactPCI system controller board based on the 2nd generation Intel® Core™ i7 and i5 processors combined with the mobile Intel® QM67 Express chipset. Two SODIMM sockets are available on the CP6003-SA to provide up to 16 GB dual-channel, third-generation Double Data Rate (DDR3) memory with Error Checking and Correction (ECC) running at 1333 MHz.
Introduction 1.2 CP6003-SA Board-Specific Information PRELIMINARY The CP6003-SA is a CompactPCI single-board computer based on the 2nd generation Intel® Core™ i7 and i5 processors and specifically designed for use in highly integrated platforms with solid mechanical interfacing for a wide range of industrial environment applications. Some of the CP6003-SA's outstanding features are: • Support for the following 2nd generation processors: • Quad-core Intel® Core™ i7-2715QE (SV), 2.
CP6003-SA 1.3 System Expansion Capabilities 1.3.1 PMC Module Introduction The CP6003-SA has a 3.3V, rear I/O capable PMC mezzanine interface configurable for either 64-bit/66 MHz PCI or 64-bit/133 MHz PCI-X operation. This interface supports a wide range of PMC modules with PCI interface including all of Kontron’s PMC modules and provides an easy and flexible way to configure the CP6003-SA for various application requirements. For information on the PMC interface, refer to chapter 2.10.
Page 1 - 6 Temp. Sense Flash IPMB I2C COMA to Front I/O COMB RS-422 LPC RST Bat. EEP uEFI BIOS Flash SIO TPM SATA 7-pin VGA CRT to VGA Switch HDA USB 2x USB 4x USB USB 2x HDMI/DVI DP to HDMI / DVI 2xDP Intel® QM67 VGA 4x HDA SATA RTC SATA SMB SPI LPC (on request) VGA Switch RS-232 to Rear I/O VGA CRT COMA RJ45 2.5" SATA SSD/HDD site Redundant FPGA Board Control GP DMI FDI Mag.
CP6003-SA 1.4.2 Introduction Front Panels Figure 1-2: CP6003-SA Front Panel Legend: IPMI LEDs I0/I1 (red/green): Indicate the software status of the IPMI controller Status LEDs TH (red/green): Temperature Status HS (blue): Hot Swap Control General Purpose LEDs LED 0..3 (red/green/amber): General Purpose/POST code Integral Ethernet LEDs ACT (green): Ethernet Link/Activity SPEED (green/orange/off): Ethernet Speed Note ...
Introduction 1.4.
CP6003-SA Figure 1-4: Introduction CP6003-SA Board Layout – Bottom View PRELIMINARY Temperature Sensor JP1 JP2 JP3 J25 ID 1044-9757, Rev. 2.
Introduction 1.5 Technical Specification Table 1-1: CP6003-SA Main Specifications FEATURES Processor and Memory CPU PRELIMINARY CP6003-SA SPECIFICATIONS The CP6003-SA supports the following 2 nd generation microprocessors: • Quad-core Intel® Core™ i7-2715QE (SV), 2.1 GHz, 6 MB L3 cache • Dual-core Intel® Core™ i7-2655LE (LV), 2.2 GHz, 4 MB L3 cache • Dual-core Intel® Core™ i5-2515E (SV), 2.
CP6003-SA CP6003-SA Main Specifications (Continued) SPECIFICATIONS Intel® QM67 Mobile Intel® QM67 Express Chipset: • Two x4 or eight x1 PCI Express 2.0 ports operating at 5 GT/s (only one x4 PCI Express port is used on the CP6003-SA) • SATA host controller with six ports and RAID 0/1/5/10 support • Two SATA 6 Gb/s ports accessible via onboard connectors • Four SATA 3 Gb/s ports accessible via rear I/O • USB 2.
Introduction Table 1-1: CP6003-SA CP6003-SA Main Specifications (Continued) FEATURES Rear I/O SPECIFICATIONS The following interfaces are routed to the rear I/O connectors J3 and J5. • COMA (RS-232 signaling) and COMB (RS-422 signaling); no buffer on the rear I/O module is necessary • 4 x USB 2.0 • 1 x CRT VGA, 2 x HDMI/DVI • 1 x HDA • 2 x Gigabit Ethernet (compliant with PICMG 2.16, R 1.
CP6003-SA CP6003-SA Main Specifications (Continued) FEATURES Front Panel Connectors • • • • • Onboard Connectors • PMC connectors J21 - J24 (Jn1 - Jn4) • XMC connector, J20 • Two SATA connectors • One 7-pin, standard SATA connector, J14 • One 34-pin, SATA extension connector, J17 • JTAG connector, J16 • Debug connector, J15 • XDP-SFF (debug) connector, J25 • CompactPCI Connectors J1 - J5, J4 optional • Two 204-pin DDR3 SODIMM sockets, J18 and J19 Sockets Switches SPECIFICATIONS VGA: 15-pin, D-Sub con
Introduction Table 1-1: CP6003-SA CP6003-SA Main Specifications (Continued) FEATURES IPMI Controller SPECIFICATIONS • NXP® ARM7 microcontroller with redundant 512 kB firmware flash and automatic roll-back strategy IPMI • The IPMI controller carries out IPMI commands such as monitoring sev• Thermal Security Software PRELIMINARY Thermal Management eral onboard temperature conditions, board voltages and the power supply status, and managing hot swap operations.
CP6003-SA Table 1-1: Introduction CP6003-SA Main Specifications (Continued) FEATURES SPECIFICATIONS Mechanical 6U, 4HP, CompactPCI-compliant form factor Power Consumption See Chapter 5 for details. Temperature Ranges Operational: 0°C to +60°C -40°C to +70°C Storage: -55°C to +85°C Standard Extended without TPM Without hard disk and without battery Note ... General Note ...
Introduction 1.6 CP6003-SA Standards The board complies with the requirements of the following standards: Table 1-2: Standards TYPE PRELIMINARY CE ASPECT STANDARD REMARKS Emission EN55022 EN61000-6-3 -- Immission EN55024 EN61000-6-2 -- Electrical Safety EN60950-1 -- Mechanical Mechanical Dimensions IEEE1101.
CP6003-SA Introduction Note ... Kontron performs comprehensive environmental testing of its products in accordance with applicable standards. Customers desiring to perform further environmental testing of Kontron products must contact Kontron for assistance prior to performing any such testing. This is necessary, as it is possible that environmental testing can be destructive when not performed in accordance with the applicable specifications.
PRELIMINARY Introduction CP6003-SA This page has been intentionally left blank. Page 1 - 18 ID 1044-9757, Rev. 2.
