Instruction Manual

ManualsBrandsKontron ManualsHardwareCP-RIO6-001-HD-VGA

If it’s embedded, it’s Kontron.

» User Guide «

CP-RIO6-001-HD-VGA

6U CompactPCI Rear Transition Module

Doc. ID: 1052-4138, Rev. 1.0

July 30, 2012

Summary of content (46 pages)

PAGE 1
» User Guide « CP-RIO6-001-HD-VGA 6U CompactPCI Rear Transition Module Doc. ID: 1052-4138, Rev. 1.0 July 30, 2012 If it’s embedded, it’s Kontron.
PAGE 2
Preface CP-RIO6-001-HD-VGA Revision History Publication Title: CP-RIO6-001-HD-VGA 6U CompactPCI Rear Transition Modules Doc. ID: 1052-4138 Rev. 1.0 Brief Description of Changes Date of Issue Initial issue 30-Jul-2012 Imprint Kontron Europe GmbH may be contacted via the following: MAILING ADDRESS TELEPHONE AND E-MAIL Kontron Europe GmbH +49 (0) 800-SALESKONTRON Sudetenstraße 7 sales@kontron.
PAGE 3
CP-RIO6-001-HD-VGA Preface Table of Contents Revision History .........................................................................................................ii Imprint ........................................................................................................................ii Disclaimer ..................................................................................................................ii Table of Contents ...............................................................
PAGE 4
Preface 2.1.4 CP-RIO6-001-HD-VGA Serial ATA Interfaces .......................................................................2 - 7 2.1.4.1 SATA Connector J13 ..............................................................2 - 7 2.1.4.2 SATA Connector J15 ..............................................................2 - 8 2.1.5 COM Interfaces ...............................................................................2 - 9 2.1.5.1 COMA Port .......................................................
PAGE 5
CP-RIO6-001-HD-VGA Preface List of Tables 1-1 CP-RIO6-001-HD-VGA Main Specifications .............................................. 1 - 6 1-2 Standards for the CP-RIO6-001-HD-VGA ................................................. 1 - 7 1-3 Related Publications .................................................................................. 1 - 8 2-1 USB Con. J16 and J17 Pinout ................................................................... 2 - 3 2-2 USB NAND Flash Con. J14 Pinout ...........
PAGE 6
Preface CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page vi ID 1052-4138, Rev. 1.
PAGE 7
CP-RIO6-001-HD-VGA Preface List of Figures 1-1 CP-RIO6-001-HD-VGA Functional Block Diagram .................................. 1 - 3 1-2 CP-RIO6-001-HD-VGA Front Panel ........................................................ 1 - 4 1-3 CP-RIO6-001-HD-VGA Board Layout – Front View ................................ 1 - 5 2-1 USB Con. J16 and J17 ............................................................................ 2 - 3 2-2 USB NAND Flash Con. J14 ...............................................
PAGE 8
Preface CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page viii ID 1052-4138, Rev. 1.
PAGE 9
CP-RIO6-001-HD-VGA Preface Proprietary Note This document contains information proprietary to Kontron. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents. The information contained in this document is, to the best of our knowledge, entirely correct.
PAGE 10
Preface CP-RIO6-001-HD-VGA Explanation of Symbols Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material. Please refer also to the section “High Voltage Safety Instructions” on the following page.
PAGE 11
CP-RIO6-001-HD-VGA Preface For Your Safety Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
PAGE 12
Preface CP-RIO6-001-HD-VGA General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
PAGE 13
CP-RIO6-001-HD-VGA Preface Two Year Warranty Kontron grants the original purchaser of Kontron’s products a TWO YEAR LIMITED HARDWARE WARRANTY as described in the following. However, no other warranties that may be granted or implied by anyone on behalf of Kontron are valid unless the consumer has the express written consent of Kontron. Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase.
PAGE 14
Preface CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page xiv ID 1052-4138, Rev. 1.
PAGE 15
CP-RIO6-001-HD-VGA Introduction Chapter 1 Introduction ID 1052-4138, Rev. 1.
PAGE 16
Introduction CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page 1 - 2 ID 1052-4138, Rev. 1.
PAGE 17
CP-RIO6-001-HD-VGA 1. Introduction 1.1 Board Overview Introduction The CP-RIO6-001-HD-VGA is a 6U CompactPCI rear transition module designed for use with Kontron 6U CompactPCI CPU boards and provide comprehensive rear I/O functionality for peripherals. In order to use these modules, a special 6U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required. The CP-RIO6-001-HD-VGA comes with three USB 2.
PAGE 18
Introduction 1.2.2 CP-RIO6-001-HD-VGA Front Panel Figure 1-2: CP-RIO6-001-HD-VGA Front Panel Page 1 - 4 ID 1052-4138, Rev. 1.
PAGE 19
CP-RIO6-001-HD-VGA 1.2.3 Introduction Board Layout Figure 1-3: CP-RIO6-001-HD-VGA Board Layout – Front View HDD/SSD rJ5 J11 DVI-D rJ4 J15 SATA rJ3 S1 J20 VGA J13 SATA 7 1 J19 COMA Magn. J18 10 9 J8 COMB 2 GbE A Magn. GbE B 1 USB 1 1 ID 1052-4138, Rev. 1.
PAGE 20
Introduction 1.3 CP-RIO6-001-HD-VGA Technical Specification Table 1-1: CP-RIO6-001-HD-VGA Main Specifications Front Panel Interfaces CP-RIO6-001-HD-VGA SPECIFICATIONS Analog Video VGA: 15-pin, D-Sub connector, J20 Ethernet Two Gigabit Ethernet interfaces implemented as a dual RJ-45 connector, J18A/B USB Two USB 2.
PAGE 21
CP-RIO6-001-HD-VGA 1.4 Introduction Standards The CP-RIO6-001-HD-VGA complies with the requirements of the following standards: Table 1-2: Standards for the CP-RIO6-001-HD-VGA TYPE CE ASPECT STANDARD REMARKS Emission EN55022 EN61000-6-3 -- Immission EN55024 EN61000-6-2 -- Electrical Safety EN60950-1 -- Mechanical Mechanical Dimensions IEEE 1101.
PAGE 22
Introduction CP-RIO6-001-HD-VGA Note ... Kontron performs comprehensive environmental testing of its products in accordance with applicable standards. Customers desiring to perform further environmental testing of Kontron products must contact Kontron for assistance prior to performing any such testing. This is necessary, as it is possible that environmental testing can be destructive when not performed in accordance with the applicable specifications.
PAGE 23
CP-RIO6-001-HD-VGA Functional Description Chapter 21 Functional Description ID 1052-4138, Rev. 1.
PAGE 24
Functional Description CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page 2 - 2 ID 1052-4138, Rev. 1.
PAGE 25
CP-RIO6-001-HD-VGA Functional Description 2. Functional Description 2.1 Board Interfaces 2.1.1 USB Interfaces The CP-RIO6-001-HD-VGA rear I/O module supports three USB 2.0 ports, two on the front I/O and one onboard for the USB NAND Flash module. All ports are high-speed, full-speed, and low-speed capable. One USB peripheral may be connected to each port. For connecting more USB devices to the CP-RIO6-001-HD-VGA than there are available ports, an external USB hub is required. Note ...
PAGE 26
Functional Description 2.1.1.2 CP-RIO6-001-HD-VGA Onboard USB NAND Flash Connector J14 The CP-RIO6-001-HD-VGA rear I/O module has one onboard USB interface implemented on a 9-pin connector, J14, with the following pinout. Figure 2-2: USB NAND Flash Con. J14 Table 2-2: USB NAND Flash Con. J14 Pinout PIN SIGNAL FUNCTION I/O 1 VCC VCC -- 9 1 3 UV0- Differential USB- I/O 5 UV0+ Differential USB+ I/O 10 2 7 GND GND -- 9 Key 2, 4, 6, 8 NC Not connected -- 10 Res.
PAGE 27
CP-RIO6-001-HD-VGA 2.1.2 Functional Description VGA Interface The CP-RIO6-001-HD-VGA provides one 15-pin, female connector, J20, on the front panel. This connector is used to connect an analog VGA (CRT) monitor to the module. The following figure illustrates the D-Sub VGA connector J20. Figure 2-3: D-Sub VGA Connector J20 6 1 11 15 5 10 The following table indicates the pinout of the D-Sub VGA connector J20.
PAGE 28
Functional Description 2.1.3 CP-RIO6-001-HD-VGA Gigabit Ethernet Interfaces The CP-RIO6-001-HD-VGA provides a Gigabit Ethernet interface implemented as one dual, RJ-45 Ethernet connector J18A/B. Figure 2-4: Dual Gigabit Ethernet Con.
PAGE 29
CP-RIO6-001-HD-VGA 2.1.4 Functional Description Serial ATA Interfaces The CP-RIO6-001-HD-VGA provides two SATA interfaces, one for connecting a standard 2.5" SATA HDD/SSD and one for connecting a SATA device via a SATA cable. The SATA interfaces are capable of supporting SATA 1.5 Gb/s and SATA 3.0 Gb/s signaling. 2.1.4.1 SATA Connector J13 The CP-RIO6-001-HD-VGA rear I/O module is equipped with a SATA connector, J13, used to connect a standard SATA device to the rear I/O module via a SATA cable.
PAGE 30
Functional Description 2.1.4.2 CP-RIO6-001-HD-VGA SATA Connector J15 The CP-RIO6-001-HD-VGA rear I/O module is equipped with the SATA connector J15 used to connect a 2.5” SATA HDD/SSD to the rear I/O module. The connector is divided into two segments, a signal segment and a power segment.
PAGE 31
CP-RIO6-001-HD-VGA 2.1.5 Functional Description COM Interfaces The CP-RIO6-001-HD-VGA rear I/O module provides two COM ports for connecting RS-232 (COMA) and RS-232/RS-422 (COMB) devices, depending on the CPU board. The following figures and tables provide pinout information for the COM connector J8 (COM B) and J19 (COMA). 2.1.5.1 COMA Port The COMA port is available on the front panel as a serial RS-232, 8-pin, RJ-45 connector Figure 2-7: Serial Con.
PAGE 32
Functional Description 2.1.5.2 CP-RIO6-001-HD-VGA COMB Port The COMB port is realized using an onboard 10-pin male header type connector, J8.
PAGE 33
CP-RIO6-001-HD-VGA 2.1.7 Functional Description Rear I/O Interface on cPCI Connectors: rJ3, rJ4 and rJ5 The CP-RIO6-001-HD-VGA rear I/O module is equipped with three CompactPCI rear I/O connectors: rJ3, rJ4 and rJ5. Note ... To support the rear I/O feature, a 6U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required. Do not plug the CP-RIO6-001-HD-VGA in a backplane without rear I/O support.
PAGE 34
Functional Description Table 2-9: CP-RIO6-001-HD-VGA Rear I/O CompactPCI Connector rJ3 Pinout PIN Z 19 NC RIO_VCC RIO_VCC RIO_3.
PAGE 35
CP-RIO6-001-HD-VGA Functional Description Table 2-11: Rear I/O CompactPCI Connector rJ4 Pinout PIN Z A B 25 NC RSV RSV GND RSV RSV GND 24 NC RSV RSV GND RSV RSV GND 23 NC NC RIO_VCC GND NC RIO_3.
PAGE 36
Functional Description CP-RIO6-001-HD-VGA Table 2-12: Rear I/O CompactPCI Connector rJ5 Pinout PIN Z A B C D E F 22 NC GPIO: * PWM1:OUT GND PWM2:OUT NC GND 21 NC NC NC GND NC SYS_WP GND 20 NC GPIO:0 NC GND GPIO:1 NC GND 19 NC GND GND GND NC NC GND 18 NC NC NC GND GND GND GND 17 NC NC NC GND NC NC GND 16 NC NC NC GND GPIO: * GPIO: * GND 15 NC NC NC GND NC NC GND 14 NC GND GND GND GND GND GND 13 NC NC NC NC NC NC GND 12
PAGE 37
CP-RIO6-001-HD-VGA 2.1.8 Functional Description GPIO Connectors J10 and J11 The CP-RIO6-001-HD-VGA has two GPIO interfaces, one on J10 (GPIO:0) and one on J11 (GPIO:1). Pin 1 is the signal and pin 2 is ground. Refer to figure 1-3 for the connector locations and pin orientation. Signal direction, input or output and voltage leveling is a function of the CPU. Filtering and signal protection must be done by the system integrator. 2.
PAGE 38
Functional Description CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page 2 - 16 ID 1052-4138, Rev. 1.
PAGE 39
CP-RIO6-001-HD-VGA Installation Chapter 31 Installation ID 1052-4138, Rev. 1.
PAGE 40
Installation CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page 3 - 2 ID 1052-4138, Rev. 1.
PAGE 41
CP-RIO6-001-HD-VGA 3. Installation Installation The CP-RIO6-001-HD-VGA has been designed for easy installation. However, the following standard precautions, installation procedures, and general information must be observed to ensure proper installation and to preclude damage to the CP-RIO6-001-HD-VGA, other system components, or injury to personnel. 3.1 Safety Requirements The following safety precautions must be observed when installing or operating the CP-RIO6001-HD-VGA.
PAGE 42
Installation 3.2 CP-RIO6-001-HD-VGA Rear I/O Module Installation Procedures To perform an installation of the rear I/O module in a system, proceed as follows: 1. Ensure that the safety requirements indicated Chapter 3.1 are observed. Warning! Failure to comply with the instruction below may cause damage to the rear I/O module or result in improper system operation. 2. Ensure that the rear I/O module is compatible with the CPU board and the backplane prior to installation. Note ...
PAGE 43
CP-RIO6-001-HD-VGA 3.3 Installation Rear I/O Module Removal Procedures To remove the rear I/O module proceed as follows: 1. Ensure that the safety requirements indicated in Chapter 3.1 are observed. Warning! Care must be taken when applying the procedures below to ensure that neither the rear I/O module nor system boards are physically damaged by the application of these procedures. 2. Ensure that no power is applied to the system before proceeding.
PAGE 44
Installation 3.4.2 CP-RIO6-001-HD-VGA USB 2.0 NAND Flash Module Installation One USB 2.0 NAND Flash module may be connected to the CP-RIO6-001-HD-VGA via the onboard USB 2.0 NAND Flash connector, J14. The USB 2.0 NAND Flash module must be physically installed on the CP-RIO6-001-HD-VGA prior to installation of the rear I/O module in a system. During installation it is necessary to ensure that the USB 2.0 NAND Flash module is properly seated in the onboard USB 2.0 NAND Flash connector, i.e.
PAGE 45
CP-RIO6-001-HD-VGA 3.4.4 Installation Installation of a 2.5” SATA HDD/SSD Device One 2.5” SATA HDD/SSD may be installed on the CP-RIO6-001-HD-VGA via the onboard SATA connector J15. During installation it is necessary to ensure that the SATA device is correctly seated in the onboard SATA connector and properly secured via the four mounting screws. The following figure shows the placement of the 2.5” SATA HDD/SSD and the USB 2.0 NAND Flash on the CP-RIO6-001-HD-VGA.
PAGE 46
Installation CP-RIO6-001-HD-VGA This page has been intentionally left blank. Page 3 - 8 ID 1052-4138, Rev. 1.