Manual

ManualsBrandsKontron ManualsHardwareCP-RIO3-05

If it’s embedded, it’s Kontron.

» User Guide «

P R E L I M I N A R Y

CP-RIO3-05

3U CompactPCI Rear Transition Module

Doc. ID: 1044-0711, Rev. 1.0

February 18, 2011

Summary of content (42 pages)

PAGE 1
CP-RIO3-05 3U CompactPCI Rear Transition Module Doc. ID: 1044-0711, Rev. 1.0 February 18, 2011 If it’s embedded, it’s Kontron.
PAGE 2
Preface CP-RIO3-04S Revision History Publication Title: CP-RIO3-05 3U CompactPCI Rear Transition Module Doc. ID: 1044-0711 Rev. PRELIMINARY 1.0 Brief Description of Changes Date of Issue Initial issue 18-Feb-2011 Imprint Kontron Modular Computers GmbH may be contacted via the following: MAILING ADDRESS TELEPHONE AND E-MAIL Kontron Modular Computers GmbH +49 (0) 800-SALESKONTRON Sudetenstraße 7 sales@kontron.
PAGE 3
CP-RIO3-05 Preface Revision History .........................................................................................................ii Imprint ........................................................................................................................ii Disclaimer ..................................................................................................................ii Table of Contents .........................................................................................
PAGE 4
Preface 3. CP-RIO3-05 2.1.6 Serial ATA Interfaces .....................................................................2 - 10 2.1.7 Rear I/O Interface on CompactPCI Connector rJ2 ........................ 2 - 11 Installation ................................................................................ 3 - 3 3.1 Safety Requirements ...............................................................................3 - 3 3.2 Initial Installation Procedures .................................................
PAGE 5
CP-RIO3-05 Preface 1-1 CP-RIO3-05 Main Specifications ............................................................... 1 - 6 1-2 Standards .................................................................................................. 1 - 7 1-3 Additional Standards for Modules Providing Ruggedized Service ............. 1 - 8 1-4 Related Publications .................................................................................. 1 - 8 2-1 D-Sub VGA Connector J8 Pinout ........................
PAGE 6
PRELIMINARY Preface CP-RIO3-05 This page has been intentionally left blank. Page vi ID 1044-0711, Rev. 1.
PAGE 7
CP-RIO3-05 Preface 1-1 CP-RIO3-05 Functional Block Diagram ................................................... 1 - 3 1-2 CP-RIO3-05 Front Panel .......................................................................... 1 - 4 1-3 CP-RIO3-05 Board Layout – Top View .................................................... 1 - 5 2-1 D-Sub VGA Connector J8 ........................................................................ 2 - 3 2-2 Gigabit Ethernet Connectors J6 and J7 ..............................
PAGE 8
PRELIMINARY Preface CP-RIO3-05 This page has been intentionally left blank. Page viii ID 1044-0711, Rev. 1.
PAGE 9
CP-RIO3-05 Preface Proprietary Note This document contains information proprietary to Kontron. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents. The information contained in this document is, to the best of our knowledge, entirely correct.
PAGE 10
Preface CP-RIO3-05 Explanation of Symbols Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material. Please refer also to the section “High Voltage Safety Instructions” on the following page.
PAGE 11
CP-RIO3-05 Preface For Your Safety Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
PAGE 12
Preface CP-RIO3-05 General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
PAGE 13
CP-RIO3-05 Preface Two Year Warranty Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase. This warranty is not transferable nor extendible to cover any other users or long-term storage of the product. It does not cover products which have been modified, altered or repaired by any other party than Kontron or their authorized agents.
PAGE 14
PRELIMINARY Preface CP-RIO3-05 This page has been intentionally left blank. Page xiv ID 1044-0711, Rev. 1.
PAGE 15
Introduction Chapter 1 Introduction ID 1044-0711, Rev. 1.
PAGE 16
PRELIMINARY Introduction CP-RIO3-05 This page has been intentionally left blank. Page 1 - 2 ID 1044-0711, Rev. 1.
PAGE 17
CP-RIO3-05 Introduction 1. Introduction 1.1 Board Overview The CP-RIO3-05 comes with four Gigabit Ethernet ports, two USB 2.0 ports, one VGA (CRT) port, and two serial ports (COM1 and COM2) on the front panel, as well as two onboard SATA ports for connection to external SATA devices, one onboard GPIO port, two onboard serial ports (COM1 and COM2), and one CompactPCI connector for connecting the CP-RIO3-05 to the backplane.
PAGE 18
Introduction 1.2.2 CP-RIO3-05 Front Panel Figure 1-2: CP-RIO3-05 Front Panel PRELIMINARY CP-RIO3-05 Note ... The Ethernet LEDs have no functionality on the CP-RIO3-05. Page 1 - 4 ID 1044-0711, Rev. 1.
PAGE 19
CP-RIO3-05 1.2.3 Introduction Board Layout Figure 1-3: CP-RIO3-05 Board Layout – Top View J8 VGA J10 GPIO J2a rJ2 CPCI SW1 Reset Button ribbon cable PRELIMINARY COM1 J7 ETH C/D J2 COM1 J6 ETH A/B 1 1 J5 SATA0 J4 SATA1 ID 1044-0711, Rev. 1.
PAGE 20
Introduction 1.
PAGE 21
CP-RIO3-05 1.4 Introduction Standards The CP-RIO3-05 complies with the requirements of the following standards. Standards TYPE CE ASPECT STANDARD Emission EN55022 EN61000-6-3 Immission EN55024 EN61000-6-2 Electrical Safety EN60950-1 Mechanical Mechanical Dimensions IEEE 1101.
PAGE 22
Introduction CP-RIO3-05 In addition, modules providing ruggedized service comply with the following standards as well. Table 1-3: Additional Standards for Modules Providing Ruggedized Service TYPE ASPECT PRELIMINARY Environmental 1.
PAGE 23
Functional Description Chapter 21 Functional Description ID 1044-0711, Rev. 1.
PAGE 24
PRELIMINARY Functional Description CP-RIO3-05 This page has been intentionally left blank. Page 2 - 2 ID 1044-0711, Rev. 1.
PAGE 25
CP-RIO3-05 Functional Description 2. Functional Description 2.1 Board Interfaces 2.1.1 VGA Interface The CP-RIO3-05 provides one 15-pin, D-Sub VGA connector, J8, on the front panel. This connector is used to connect an analog VGA (CRT) monitor to the CP-RIO3-05. The following figure illustrates the D-Sub VGA connector J8. Figure 2-1: D-Sub VGA Connector J8 6 PRELIMINARY 1 11 15 5 10 The following table indicates the pinout of the D-Sub VGA connector J8.
PAGE 26
Functional Description 2.1.2 CP-RIO3-05 Gigabit Ethernet Interfaces The CP-RIO3-05 provides two dual Gigabit Ethernet connectors J6 (ETH A / ETH B) and J7 (ETH C / ETH D) realized as two dual RJ-45 connectors. The interfaces provide automatic detection and switching between 10Base-T, 100Base-TX and 1000Base-T data transmission (Auto-Negotiation). Auto-wire switching for crossed cables is also supported (Auto MDI-X). Figure 2-2: GbE Connectors J6 and J7 Table 2-2: Pinout of GbE Con.
PAGE 27
CP-RIO3-05 2.1.3 Functional Description USB Interfaces The CP-RIO3-05 provides two identical USB interfaces implemented as a dual USB connector J9 (USB0/USB1). Both interfaces provide a maximum transfer rate of 480 Mb/s for connecting USB devices. One USB peripheral may be connected to each port. To connect more USB devices than there are available ports, an external hub is required.
PAGE 28
Functional Description 2.1.4 CP-RIO3-05 COM Interfaces The CP-RIO3-05 module provides two COM ports, COM1 and COM2, on the front panel for connecting RS-232/RS-422 devices. The COM ports are realized as 9-pin D-Sub connectors, J2a and J3a, and connected via flat cables to the 10-pin onboard connectors, J2 and J3. COM1 is a full-featured RS-232 interface. COM2 is an RS-422 interface switchable to limited RS-232 via the uEFI BIOS of the CP3002-RC/CP3002-RA.
PAGE 29
CP-RIO3-05 Functional Description Table 2-5: D-Sub COM Connector J3a (COM2) Pinout I/O DESCRIPTION PIN SIGNAL RS-422 SIGNAL DESCRIPTION I/O -- Not connected NC 1 NC Not connected -- I Receive data RXD 2 RXD+ Receive data + I O Transmit data TXD 3 TXD- Transmit data - O -- Not connected NC 4 NC Not connected -- -- Signal ground GND 5 GND Signal ground -- -- Not connected NC 6 NC Not connected -- O Request to send RTS 7 TXD+ Transmit data + O I Clear
PAGE 30
Functional Description CP-RIO3-05 PRELIMINARY Table 2-6: Onboard Serial Port Connector J2 (COM1) Pinout PIN SIGNAL DESCRIPTION I/O 1 DCD Data carrier detect I 2 DSR Data send request I 3 RXD Receive data I 4 RTS Request to send O 5 TXD Transmit data O 6 CTS Clear to send I 7 DTR Data terminal ready O 8 RI Ring indicator I 9 GND Signal ground -- 10 NC Not connected -- Table 2-7: Onboard Serial Port Connector J3 (COM2) Pinout RS-232 I/O DESCRIPTION SIGNAL PIN
PAGE 31
CP-RIO3-05 2.1.5 Functional Description General Purpose Input/Output Port The CP-RIO3-05 module provides one general purpose input/output port with five general purpose inputs and three general purpose outputs. The GPIO port is implemented as a 10-pin onboard connector J10. Note ... The GPI signals tolerate only 3.3 V signaling and the inputs have internal pullup resistors. The GPI and GPO signals support LVTTL signaling.
PAGE 32
Functional Description 2.1.6 CP-RIO3-05 Serial ATA Interfaces The CP-RIO3-05 provides two onboard SATA II interfaces implemented as two onboard SATA connectors, J4 and J5, used to connect standard SATA devices via SATA cables. A SATA II repeater is provided on the CP-RIO3-05 to improve the signal performance. The following figure and table provide pinout information for the SATA connectors J4 and J5. Figure 2-7: SATA Con.
PAGE 33
CP-RIO3-05 2.1.7 Functional Description Rear I/O Interface on CompactPCI Connector rJ2 The CP-RIO3-05 is equipped with one CompactPCI rear I/O connector rJ2. Warning! To support the rear I/O feature, a 3U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required. Do not plug the CP-RIO3-05 in a backplane without rear I/O support. Failure to comply with the above will result in damage to the CP-RIO3-05.
PAGE 34
Functional Description CP-RIO3-05 PRELIMINARY Table 2-10: Rear I/O CompactPCI Bus Connector rJ2 Pinout PIN ROW Z ROW A ROW B ROW C ROW D ROW E ROW F 22 NC NC NC NC NC NC GND 21 NC GPI4 GND USB1+ USB0+ USB1_PWR_5V GND 20 NC GPO1 GND USB1- USB0- USB0_PWR_5V GND 19 NC GND GND RIO_3.3V (BAT) GPI2 RIO_3.
PAGE 35
CP-RIO3-05 Functional Description Legend for Table 2-10: Serial ATA port lPx Gigabit Ethernet port VGAx VGA signals COM1x COM1 port (corresponds to COMA on the CP3002-RA/-CP3002-RC) COM2x COM2 port (corresponds to COMB on the CP3002-RA/-CP3002-RC) PWRx Power Management signals RIO_5V/3.3V Power GPIx General purpose input signal GPOx General purpose output signal ID 1044-0711, Rev. 1.
PAGE 36
PRELIMINARY Functional Description CP-RIO3-05 This page has been intentionally left blank. Page 2 - 14 ID 1044-0711, Rev. 1.
PAGE 37
Installation Chapter 31 Installation ID 1044-0711, Rev. 1.
PAGE 38
PRELIMINARY Installation CP-RIO3-05 This page has been intentionally left blank. Page 3 - 2 ID 1044-0711, Rev. 1.
PAGE 39
CP-RIO3-05 3. Installation Installation The CP-RIO3-05 has been designed for easy installation. However, the following standard precautions, installation procedures, and general information must be observed to ensure proper installation and to preclude damage to the CP-RIO3-05, other system components, or injury to personnel. 3.1 Safety Requirements The following safety precautions must be observed when installing or operating the CP-RIO305.
PAGE 40
Installation 3.2 CP-RIO3-05 Initial Installation Procedures The following procedures are applicable only for the initial installation of the CP-RIO3-05 in a system. To perform an initial installation of both the CP-RIO3-05 in a system, proceed as follows: 1. Ensure that the safety requirements indicated in Chapter 3.1 are observed. Warning! Failure to comply with the instruction below may cause damage to the CP-RIO3-05 or result in improper system operation. PRELIMINARY 2.
PAGE 41
CP-RIO3-05 3.3 Installation Standard Removal Procedures To remove the CP-RIO3-05 proceed as follows: 1. Ensure that the safety requirements indicated in Chapter 3.1 are observed. Warning! Care must be taken when applying the procedures below to ensure that neither the CP-RIO3-05 nor system boards are physically damaged by the application of these procedures. 2. Ensure that no power is applied to the system before proceeding.
PAGE 42
Installation 3.4 CP-RIO3-05 Installation of External Serial ATA Devices Up to two external SATA devices may be connected to the CP-RIO3-05 via the onboard SATA connectors J4 and J5 as well as the appropriate SATA cables. Some symptoms of incorrectly installed SATA devices are: • Device on a SATA channel does not spin up: check power cables and cabling. May also result from a bad power supply or SATA device. The SATA connector on the CP-RIO3-05 provides only a data connection.