» User Guide « CP-RIO3-04S 3U CompactPCI Rear Transition Module Doc. ID: 1036-1669, Rev. 1.0 December 14, 2009 If it’s embedded, it’s Kontron.
Preface CP-RIO3-04S Revision History Publication Title: CP-RIO3-04S 3U CompactPCI Rear Transition Module Doc. ID: 1036-1669 Rev. 1.0 Brief Description of Changes Date of Issue Initial issue 14-Dec-2009 Imprint Kontron Modular Computers GmbH may be contacted via the following: MAILING ADDRESS TELEPHONE AND E-MAIL Kontron Modular Computers GmbH +49 (0) 800-SALESKONTRON Sudetenstraße 7 sales@kontron.
CP-RIO3-04S Preface Table of Contents Revision History .........................................................................................................ii Imprint ........................................................................................................................ii Disclaimer ..................................................................................................................ii Table of Contents ......................................................................
Preface 2.1.6 3. CP-RIO3-04S Rear I/O Interface on CompactPCI Connectors rJ2 ........................2 - 9 Installation ................................................................................ 3 - 3 3.1 Safety Requirements ...............................................................................3 - 3 3.2 Initial Installation Procedures ...................................................................3 - 4 3.3 Standard Removal Procedures ..................................................
CP-RIO3-04S Preface List of Tables 1-1 CP-RIO3-04S Main Specifications ............................................................ 1 - 6 1-2 Standards for the CP-RIO3-04S ................................................................ 1 - 7 1-3 Related Publications .................................................................................. 1 - 8 2-1 D-Sub VGA Connector J7 Pinout ..............................................................
Preface CP-RIO3-04S This page has been intentionally left blank. Page vi ID 1036-1669, Rev. 1.
CP-RIO3-04S Preface Proprietary Note This document contains information proprietary to Kontron. It may not be copied or transmitted by any means, disclosed to others, or stored in any retrieval system or media without the prior written consent of Kontron or one of its authorized agents. The information contained in this document is, to the best of our knowledge, entirely correct.
Preface CP-RIO3-04S Explanation of Symbols Caution, Electric Shock! This symbol and title warn of hazards due to electrical shocks (> 60V) when touching products or parts of them. Failure to observe the precautions indicated and/or prescribed by the law may endanger your life/health and/or result in damage to your material. Please refer also to the section “High Voltage Safety Instructions” on the following page.
CP-RIO3-04S Preface For Your Safety Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
Preface CP-RIO3-04S General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the device, which are not explicitly approved by Kontron and described in this manual or received from Kontron’s Technical Support as a special handling instruction, will void your warranty.
CP-RIO3-04S Preface Two Year Warranty Kontron grants the original purchaser of Kontron’s products a TWO YEAR LIMITED HARDWARE WARRANTY as described in the following. However, no other warranties that may be granted or implied by anyone on behalf of Kontron are valid unless the consumer has the express written consent of Kontron. Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 24 consecutive months from the date of purchase.
Preface CP-RIO3-04S This page has been intentionally left blank. Page xii ID 1036-1669, Rev. 1.
CP-RIO3-04S Introduction Chapter 1 Introduction ID 1036-1669, Rev. 1.
Introduction CP-RIO3-04S This page has been intentionally left blank. Page 1 - 2 ID 1036-1669, Rev. 1.
CP-RIO3-04S Introduction 1. Introduction 1.1 Board Overview The CP-RIO3-04S 3U CompactPCI rear transition module has been designed for use with the CP305, CP307, and CP308 3U CompactPCI CPU boards from Kontron and provides comprehensive rear I/O functionality for peripherals. In order to use the CP-RIO3-04S, a 3U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required.
Introduction 1.2.2 CP-RIO3-04S Front Panel Figure 1-2: CP-RIO3-04S Front Panel CP-RIO3-04S Page 1 - 4 ID 1036-1669, Rev. 1.
CP-RIO3-04S 1.2.3 Introduction Board Layout Figure 1-3: CP-RIO3-04S Board Layout – Top View J2 COM1 J13 Peripheral Control rJ2 CPCI J10A Dual GbE J10B J3 COM2 1 J5 J7 VGA 1 J6 SATA ID 1036-1669, Rev. 1.
Introduction 1.
CP-RIO3-04S 1.4 Introduction Standards The CP-RIO3-04S complies with the requirements of the following standards: Table 1-2: Standards for the CP-RIO3-04S TYPE CE ASPECT STANDARD REMARKS / TEST PARAMETERS Emission EN55022 EN61000-6-3 -- Immission EN55024 EN61000-6-2 -- Electrical Safety EN60950-1 -- Mechanical Mechanical Dimensions IEEE 1101.
Introduction 1.5 CP-RIO3-04S Related Publications The following publications contain information relating to the CP-RIO3-04S. Table 1-3: Related Publications PRODUCT PUBLICATION CompactPCI Systems and Boards CompactPCI Specification 2.0, Rev. 3.0 All Kontron products Product Safety and Implementation Guide, ID 1021-9142 Page 1 - 8 Kontron CompactPCI Backplane Manual, ID 24229 ID 1036-1669, Rev. 1.
CP-RIO3-04S Functional Description Chapter 21 Functional Description ID 1036-1669, Rev. 1.
Functional Description CP-RIO3-04S This page has been intentionally left blank. Page 2 - 2 ID 1036-1669, Rev. 1.
CP-RIO3-04S Functional Description 2. Functional Description 2.1 Board Interfaces 2.1.1 VGA Interface The CP-RIO3-04S provides one 15-pin, D-Sub VGA connector, J7, on the front panel. This connector is used to connect an analog VGA (CRT) monitor to the CP-RIO3-04S. The following figure illustrates the D-Sub VGA connector J7. Figure 2-1: D-Sub VGA Connector J7 6 1 11 15 5 10 The following table indicates the pinout of the D-Sub VGA connector J7.
Functional Description 2.1.2 CP-RIO3-04S Gigabit Ethernet Interfaces Figure 2-2: Gigabit Ethernet Connector J10A/B The CP-RIO3-04S provides one dual Gigabit Ethernet connector J10A/B realized as two RJ-45 connectors. The interfaces provide automatic detection and switching between 10Base-T, 100Base-TX and 1000Base-T data transmission (Auto-Negotiation). Auto-wire switching for crossed cables is also supported (Auto MDI-X).
CP-RIO3-04S 2.1.3 Functional Description COM Interfaces The CP-RIO3-04S provides two COM ports, COM1 and COM2, for connecting RS-232 devices. COM1 is available on the front panel and is implemented as an RJ-45 connector, J2. COM2 is available onboard and is implemented as a 10-pin connector, J3. The following figure illustrates the RJ-45, serial port connector, J2 (COM1).
Functional Description CP-RIO3-04S The following figure illustrates the onboard serial port connector J3 (COM2). Figure 2-4: Serial Port Connector J3 (COM2) 10 9 2 1 J3 COM 2 The following table indicates the pinout of the onboard serial port connector J3 (COM2).
CP-RIO3-04S 2.1.4 Functional Description Peripheral Control Interface A fan for system cooling and a power supply with power management can be connected to the CP-RIO3-04S via the peripheral control connector J13. The following figure illustrates the peripheral control connector J13. Figure 2-5: Peripheral Control Connector J13 9 1 10 2 The following table indicates the pinout of the peripheral control connector J13.
Functional Description 2.1.5 CP-RIO3-04S Serial ATA Interfaces The CP-RIO3-04S provides two onboard SATA II interfaces implemented as two onboard SATA connectors, J5 and J6, used to connect standard SATA devices via a SATA cable. A SATA II repeater is provided on the CP-RIO3-04S to improve the signal performance. The following figure and table provide pinout information for the SATA connectors J5 and J6. Figure 2-6: SATA Con.
CP-RIO3-04S 2.1.6 Functional Description Rear I/O Interface on CompactPCI Connectors rJ2 The CP-RIO3-04S is equipped with one CompactPCI rear I/O connector rJ2. Warning! To support the rear I/O feature, a 3U CompactPCI backplane with rear I/O support as well as a compatible and correctly configured CPU board are required. Do not plug the CP-RIO3-04S in a backplane without rear I/O support. Failure to comply with the above will result in damage to the CP-RIO3-04S.
Functional Description Table 2-7: CP-RIO3-04S Rear I/O CompactPCI Connector rJ2 Pinout PIN ROW Z ROW A ROW B ROW C ROW D ROW E ROW F 22 NC NC NC NC NC NC GND 21 NC NC GND NC NC NC GND 20 NC NC GND NC NC NC GND 19 NC GND GND PWR_BTN# / out PWR_SLPS3# / in RIO_3.
CP-RIO3-04S Functional Description Legend for Table 2-7: SATAx Serial ATA port lPx Gigabit Ethernet port VGAx VGA signals COM1x COM1 port COM2x COM2 port PWRx Power Management signals 5V/3.3V Power GPIO_CFG0 GPIO configuration (configured for COM2) ID 1036-1669, Rev. 1.
Functional Description CP-RIO3-04S This page has been intentionally left blank. Page 2 - 12 ID 1036-1669, Rev. 1.
CP-RIO3-04S Installation Chapter 31 Installation ID 1036-1669, Rev. 1.
Installation CP-RIO3-04S This page has been intentionally left blank. Page 3 - 2 ID 1036-1669, Rev. 1.
CP-RIO3-04S 3. Installation Installation The CP-RIO3-04S has been designed for easy installation. However, the following standard precautions, installation procedures, and general information must be observed to ensure proper installation and to preclude damage to the CP-RIO3-04S, other system components, or injury to personnel. 3.1 Safety Requirements The following safety precautions must be observed when installing or operating the CP-RIO304S.
Installation 3.2 CP-RIO3-04S Initial Installation Procedures The following procedures are applicable only for the initial installation of the CP-RIO3-04S in a system. To perform an initial installation of both the CP-RIO3-04S in a system, proceed as follows: 1. Ensure that the safety requirements indicated in Chapter 3.1 are observed. Warning! Failure to comply with the instruction below may cause damage to the CP-RIO3-04S or result in improper system operation. 2.
CP-RIO3-04S 3.3 Installation Standard Removal Procedures To remove the CP-RIO3-04S proceed as follows: 1. Ensure that the safety requirements indicated in Chapter 3.1 are observed. Warning! Care must be taken when applying the procedures below to ensure that neither the CP-RIO3-04S nor system boards are physically damaged by the application of these procedures. 2. Ensure that no power is applied to the system before proceeding.
Installation 3.4 CP-RIO3-04S Installation of External Serial ATA Devices Up to two external SATA devices may be connected to the CP-RIO3-04S via the onboard SATA connectors J5 and J6 as well as the appropriate SATA cables. Some symptoms of incorrectly installed SATA devices are: • Device on a SATA channel does not spin up: check power cables and cabling. May also result from a bad power supply or SATA device. The SATA connector on the CP-RIO3-04S provides only a data connection.
