User guide

ManualsBrandsKontron ManualsHardware986LCD-M-mITX (BGA)

986LCD-M Family

KTD-N0837-B

Public

User Manual

Date: 2012-04-17

Page

1 of 91

986LCD-M/Flex

986LCD-M/mITX

986LCD-M/ATXE

986LCD-M/ATXP

986LCD-M/mITX BGA

User Manual

for the Motherboards:

Summary of content (91 pages)

PAGE 1
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 1 of 91 User Manual for the Motherboards: 986LCD-M/mITX 986LCD-M/mITX BGA 986LCD-M/Flex 986LCD-M/ATXE 986LCD-M/ATXP
PAGE 2
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 2 of 91 Document revision history. Revision Date By th MLA th MLA B Apr. 17 2012 A Jan. 10 2012 Comment Added information that 986LCD-M/mITX having CF socket no longer support PCIe x16 slot. KTD-00691-Z is now replaced by KTD-N0837-A. Update UL info for ATXP version. Added BIOS setting: Staggered Spinup delay Copyright Notice: Copyright  2006, KONTRON Technology A/S, ALL RIGHTS RESERVED.
PAGE 3
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 3 of 91 Life Support Policy KONTRON Technology’s PRODUCTS ARE NOT FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL OF THE GENERAL MANAGER OF KONTRON Technology A/S. As used herein: 1.
PAGE 4
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 4 of 91 Table of contents: 1. INTRODUCTION ......................................................................................................................................... 7 2. INSTALLATION PROCEDURE .................................................................................................................. 8 3. 4. 2.1 Installing the board .........................................................................
PAGE 5
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 5 of 91 Serial Ports ....................................................................................................................................... 41 4.9 4.9.1 Com1 (Port1) DB9 Connector. .................................................................................................... 41 4.9.2 Com2, Com3 & Com4 Pin Header Connectors. ......................................................................... 41 4.
PAGE 6
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 6 of 91 BIOS CONFIGURATION / SETUP ........................................................................................................... 65 8. 8.1 Introduction ...................................................................................................................................... 65 8.2 Main Menu...................................................................................................................
PAGE 7
986LCD-M Family KTD-N0837-B 1. Public User Manual Date: 2012-04-17 Page 7 of 91 Introduction This manual describes the 986LCD-M/Flex, 986LCD-M/ATXP, 986LCD-M/ATXE and 986LCD-M/mITX boards made by KONTRON Technology A/S. The boards will also be denoted 986LCD family if no differentiation is required. All boards are to be used with the Intel® Core™Duo, Intel® Core™ 2 Duo, Intel® Core™Solo and Celeron® M Processors. These belong to the Intel Yonah and Merom processor families.
PAGE 8
986LCD-M Family KTD-N0837-B Public User Manual 2. Installation procedure 2.1 Installing the board Date: 2012-04-17 Page 8 of 91 To get the board running, follow these steps. In some cases the board shipped from KONTRON Technology has CPU, DDR DRAM and Cooler mounted. In this case Step 2-4 can be skipped. 1. Turn off the power supply. ! Warning: Turn off PSU (Power Supply Unit) completely (no mains power connected to the PSU) or leave the Power Connectors unconnected while configuring the board.
PAGE 9
86LCD-M Family KTD-N0837-B 2.
PAGE 10
986LCD-M Family KTD-N0837-B 3. Public User Manual Date: 2012-04-17 Page 10 of 91 System specification 3.1 Component main data The table below summarises the features of the 986LCD-M/mITX, 986LCD-M/Flex, 986LCD-M/ATXP and 986LCD-M/ATXE embedded motherboards. Form factor Processor Memory Chipset Video Audio 986LCD-M/mITX: mini ITX (170.18millimeters by 170.
PAGE 11
986LCD-M Family KTD-N0837-B I/O Control Peripheral interfaces LAN Support BIOS Expansion Capabilities Hardware Monitor Subsystem Public User Manual Date: 2012-04-17 Page 11 of 91 Winbond W83627THF LPC Bus I/O Controller • Four USB 2.0 ports on I/O area • Four USB 2.
PAGE 12
986LCD-M Family KTD-N0837-B Operating Systems Support Environmental Conditions Public User Manual Date: 2012-04-17 Page 12 of 91 • Win2000 • WinXP • Win2003 • WinXP Embedded • WinCE.net (limitations may apply) • Linux: Feodora Core 5, Suse 10.01 (limitations may apply) Operating: 0°C – 60°C operating temperature (forced cooling). It is the customer’s responsibility to provide sufficient airflow around each of the components to keep them within allowed temperature range.
PAGE 13
986LCD-M Family KTD-N0837-B 3.2 Public User Manual Date: 2012-04-17 Page 13 of 91 Processor support table.
PAGE 14
986LCD-M Family KTD-N0837-B 3.3 Public User Manual Date: 2012-04-17 Page 14 of 91 System Memory support The 986LCD-M boards have two onboard DDR2 DIMM sockets and support the following memory features: • • • • • • 1.
PAGE 15
986LCD-M Family KTD-N0837-B 3.
PAGE 16
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 16 of 91
PAGE 17
986LCD-M Family KTD-N0837-B 3.6 Public User Manual Date: 2012-04-17 Page 17 of 91 Power Consumption In order to ensure safe operation of the board, the ATX power supply must monitor the supply voltage and shut down if the supplies are out of range – refer to the hardware manual for actual power specification.
PAGE 18
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 986LCD-M/mITX with Core Duo (T2500) & 1GB DDR2 Ram test results: Test DOS, Idle, mean Supply +12V +5V +3V3 -12V 5VSB WinXP, 3DMARK2000 & CPUBURN, mean +12V +5V +3V3 -12V 5VSB WinXP, 3DMARK2000 & CPUBURN, peak +12V +5V +3V3 -12V 5VSB S1, mean +12V +5V +3V3 -12V 5VSB S3, mean +12V +5V +3V3 -12V 5VSB S4, mean +12V +5V +3V3 +-12V 5VSB Inrush, peak +12V +5V +3V3 -12V 5VSB Current draw 0.88A 1.48A 1.22A 0.05A 0A Total 2.
PAGE 19
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 986LCD-M/mITX with w/1.06GHz Celeron M 512MB test results: Test DOS, Idle, mean Supply +12V +5V +3V3 -12V 5VSB WinXP, 3DMARK2000 & CPUBURN, mean +12V +5V +3V3 -12V 5VSB WinXP, 3DMARK2000 & CPUBURN, peak +12V +5V +3V3 -12V 5VSB S1, mean +12V +5V +3V3 -12V 5VSB S3, mean +12V +5V +3V3 -12V 5VSB S4, mean +12V +5V +3V3 +-12V 5VSB Inrush, peak +12V +5V +3V3 -12V 5VSB Current draw 0.36A 1.37A 1.31A 0A 0A Total 0.4A 1.47A 1.
PAGE 20
986LCD-M Family KTD-N0837-B 3.
PAGE 21
986LCD-M Family KTD-N0837-B 4. Public User Manual Date: 2012-04-17 Page 21 of 91 Connector Definitions The following sections provide pin definitions and detailed description of all on-board connectors. . The connector definitions follow the following notation: Column name Description Pin Shows the pin-numbers in the connector. The graphical layout of the connector definition tables is made similar to the physical connectors. Signal The mnemonic name of the signal at the current pin.
PAGE 22
986LCD-M Family KTD-N0837-B 4.1 4.1.1 Public User Manual Date: 2012-04-17 Page 22 of 91 Connector layout 986LCD-M/mITX Mini-PCIe (backside of 986LCD-M/mITX) (Support for modules with no components mounted on backside).
PAGE 23
986LCD-M Family KTD-N0837-B 4.1.2 Public User Manual Date: 2012-04-17 Page 23 of 91 986LCD-M/mITX BGA Same connectors available as on the standard 986LCD-M/mITX, except that CPU socket is replaced with BGA version of CPU. (Passive cooler included).
PAGE 24
986LCD-M Family KTD-N0837-B 4.1.
PAGE 25
986LCD-M Family KTD-N0837-B 4.1.
PAGE 26
986LCD-M Family KTD-N0837-B 4.1.
PAGE 27
986LCD-M Family KTD-N0837-B 4.2 Public User Manual Date: 2012-04-17 Page 27 of 91 Power Connector (ATXPWR) The 986LCD-M boards are designed to be supplied from a standard ATX or BTX power supply.
PAGE 28
986LCD-M Family KTD-N0837-B 4.3 Public User Manual Date: 2012-04-17 Page 28 of 91 Keyboard and PS/2 mouse connectors Attachment of a keyboard or PS/2 mouse adapter can be done through the stacked PS/2 mouse and keyboard connector (MSE & KBD). Both interfaces utilize open-drain signaling with on-board pull-up. The PS/2 mouse and keyboard is supplied from 5V_STB when in standby mode in order to enable keyboard or mouse activity to bring the system out from power saving states.
PAGE 29
986LCD-M Family KTD-N0837-B 4.4 Public User Manual Date: 2012-04-17 Page 29 of 91 Display Connectors The 986LCD-M board family provides onboard two basic types of interfaces to a display: Analog CRT interface and a digital interface typically used with flat panels. The digital interface to flat panels can be achieved through the onboard LVDS dual channel interface and/or the SDVO port available on the PCI Express connector. 4.4.
PAGE 30
986LCD-M Family KTD-N0837-B 4.4.2 Public User Manual Date: 2012-04-17 Page 30 of 91 TV-Out (Optional) Optionally the 986LCD-M board include TV-Out connector with support for Component, S-Video and Composite Output interfaces and NTSC/ PAL output format. The Intel® 945GM chipset include Macrovision support. IMPORTANT: If the TV-Out option is available then you must make agreement with Macrovision (http://www.macrovision.com/) about lincence fee.
PAGE 31
986LCD-M Family KTD-N0837-B 4.4.3 Public User Manual Date: 2012-04-17 Page 31 of 91 LVDS Flat Panel Connector (LVDS) Note Max. 0.5A Max. 0.5A Max. 0.5A Max. 0.5A Max. 0.5A 4K7Ω, 3.3V 3.3V level 3.3V level Note 1 Max. 0.5A Note 1 Max. 0.
PAGE 32
986LCD-M Family KTD-N0837-B 4.5 4.5.1 Public User Manual Date: 2012-04-17 Page 32 of 91 PCI-Express Connectors PCI-Express x16/ SDVO connector The 986LCD-M boards supports one 16-lane (x16) PCI Express port for external PCI Express based graphics boards or ADD2 devices. PCIe x16 is not available on 986LCD-M/mITX versions 810200-45xx-R18 and 810203-45xx-R18 and later revisions (because of mechanical conflict with CF socket).
PAGE 33
986LCD-M Family KTD-N0837-B Public User Manual PEG_TXP[5] PEG_TXN[5] GND GND PEG_TXP[4] PEG_TXN[4] GND GND PEG_TXP[3] PEG_TXN[3] GND GND PEG_TXP[2] PEG_TXN[2] GND GND PEG_TXP[1] PEG_TXN[1] GND GND PEG_TXP[0] PEG_TXN[0] GND NC NC 4.5.
PAGE 34
986LCD-M Family KTD-N0837-B Public User Manual GND GND NC NC GND GND NC NC GND GND NC NC GND NC GND NC NC GND GND NC NC GND GND NC NC GND GND NC NC GND GND NC NC GND GND NC NC GND GND NC NC GND GND NC NC GND NC NC Date: 2012-04-17 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55
PAGE 35
986LCD-M Family KTD-N0837-B 4.5.3 Public User Manual Date: 2012-04-17 Page 35 of 91 miniPCI-Express connector The 986LCD-M/mITX and the 986LCD-M/ATXP supports one miniPCI Express port. Note Type Signal PIN Signal WAKE# NC NC NC GND PCIE_mini CLK# PCIE_mini CLK GND 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 +3V3 GND +1.
PAGE 36
986LCD-M Family KTD-N0837-B 4.6 Public User Manual Date: 2012-04-17 Page 36 of 91 Parallel ATA harddisk interface One parallel primary ATA harddisk controller is available on the board. Standard 3½” harddisks or CD-ROM drives may be attached to the primary controller board by means of the 40 pin IDC connectors, IDE_P. The primary controller is shared between the IDE_P connector and the backside Compact Flash connector (986LCD-M/mITX only).
PAGE 37
986LCD-M Family KTD-N0837-B 4.6.1 Public User Manual Date: 2012-04-17 Page 37 of 91 IDE Hard Disk Connector (IDE_P) This connector can be used for connection of two primary IDE drives. If Compact Flash connector (986LCDM/mITX only) is utilized, only one IDE device is supported.
PAGE 38
986LCD-M Family KTD-N0837-B 4.6.2 Public User Manual Date: 2012-04-17 Page 38 of 91 CF Connector (CF) This connector is mounted on the backside of the 986LCD-M/mITX only. If a Compact Flash Disk is used, only one IDE device is supported on the IDE_P connector. The CF socket support DMA/UDMA CF modules. CF is only available on some versions of 986LCD-M/mITX (PN 810200 and PN 810203). Please notice that PCIe x16 is not available on the versions 810200-45xx-R18 and 810203-45xx-R18 and later revisions.
PAGE 39
986LCD-M Family KTD-N0837-B 4.7 Public User Manual Date: 2012-04-17 Page 39 of 91 Serial ATA harddisk interface The 986LCD-M boards have an intergrated SATA Host controller that supports independent DMA operation on four ports and data transfer rates of up to 3.0Gb/s (300MB/s). The SATA controller supports AHCI mode and has integrated RAID functionality with support for RAID modes 0, 1, 5 and 10 (Linux O/S only support for RAID 0 and 1). 4.7.
PAGE 40
986LCD-M Family KTD-N0837-B 4.8 Public User Manual Date: 2012-04-17 Page 40 of 91 Printer Port Connector (PRINTER).
PAGE 41
986LCD-M Family KTD-N0837-B 4.9 Public User Manual Date: 2012-04-17 Page 41 of 91 Serial Ports Four RS232 serial ports are available on the 986LCD-M boards The typical interpretation of the signals in the COM ports is as follows: Signal Description TxD Transmitte Data, sends serial data to the device. The signal is set to a marking state on hardware reset when the transmitter is empty or when loop mode operation is initiated. RxD Receive Data, receives serial data from the communication link.
PAGE 42
986LCD-M Family KTD-N0837-B 4.10 Public User Manual Date: 2012-04-17 Page 42 of 91 Ethernet connectors. The 986LCD-M/mITX and 986LCD-M/ATXP boards supports 3 channels of 10/100/1000Mb Ethernet RTL8111B LAN controllers. The 986LCD-M/Flex and 986LCD-M/ATXE boards supports 2 channels of 10/100/1000Mb Ethernet RTL8111B LAN controllers.
PAGE 43
986LCD-M Family KTD-N0837-B 4.10.2 Public User Manual Date: 2012-04-17 Page 43 of 91 Ethernet connector 2/3 (ETHER2/3) The two Ethernet channels in ETHER2/3 are supported by two discrete Ethernet controllers (RTL8111B) connected to the onboard PCI bus.
PAGE 44
986LCD-M Family KTD-N0837-B 4.11 Public User Manual Date: 2012-04-17 Page 44 of 91 Firewire/ IEEE-1394 connectors. The 986LCD-M boards supports two IEEE Std 1394a-2000 fully compliant cable ports at 100M bits/s, 200M bits/s, and 400M bits/s. 4.11.
PAGE 45
986LCD-M Family KTD-N0837-B 4.12 Public User Manual Date: 2012-04-17 Page 45 of 91 USB Connector (USB) The 986LCD-M boards contains an Enhanced Host Controller Interface (EHCI) host controller that supports USB 2.0 allowing data transfers up to 480Mb/s. The 986LCD-M boards also contains four Universal Host Controller Interface (UHCI Revision 1.1) controllers that support USB full-speed and low-speed signaling. The 986LCD-M boards supports a total of eight USB 2.0 ports.
PAGE 46
986LCD-M Family KTD-N0837-B 4.12.2 Public User Manual Date: 2012-04-17 Page 46 of 91 USB Connector 4/5 (USB4/5) USB Ports 4 and 5 are mounted together with IEEE1394_0 port. Note Pull U/D Ioh/Iol Type Signal 1 /15K 0.25/2 PWR IO 5V/SB5V USB5- 1 /15K 0.25/2 PWR IO 5V/SB5V USB4- PIN 1 2 1 2 3 3 Signal Type Ioh/Iol Pull U/D GND USB5+ PWR IO 0.25/2 /15K GND USB4+ PWR IO 0.25/2 /15K Note 4 4 Note 1: The 5V supply for the USB devices is on-board fused with a 1.
PAGE 47
986LCD-M Family KTD-N0837-B 4.13 Public User Manual Date: 2012-04-17 Page 47 of 91 Audio Connector 4.13.1 Audio Line-in, Line-out and Microphone Audio Line-in, Line-out and Microphone are available in the stacked audio jack connector. Below is shown audio stack configuration when configured for 8-channel audio.
PAGE 48
986LCD-M Family KTD-N0837-B 4.13.2 Public User Manual Date: 2012-04-17 Page 48 of 91 CD-ROM Audio input (CDROM) CD-ROM audio input may be connected to this connector. It may also be used as a secondary line-in signal. PIN Signal Type Ioh/Iol 1 2 3 4 CD_Left CD_GND CD_GND CD_Right IA IA IA IA - Pull U/D - Note 1 1 Note 1: The definition of which pins are use for the Left and Right channels is not a worldwide accepted standard. Some CDROM cable kits expect reverse pin order.
PAGE 49
986LCD-M Family KTD-N0837-B 4.13.
PAGE 50
986LCD-M Family KTD-N0837-B 4.14 Public User Manual Date: 2012-04-17 Page 50 of 91 Fan connectors , FAN_CPU and FAN_SYS. The FAN_CPU is used for connection of the active cooler for the CPU. The FAN_SYS can be used to power, control and monitor a fan for chassis ventilation etc. PIN 1 2 3 Signal SENSE 12V GND Type PWR PWR PWR Ioh/Iol - Pull U/D 4K7 - Note Signal description: Signal Description 12V +12V supply for fan, can be turned on/off or modulated (PWM) by the chipset.
PAGE 51
986LCD-M Family KTD-N0837-B 4.16 Note 4.17 Note Public User Manual Date: 2012-04-17 Page 51 of 91 TPM connector (unsupported). Pull U/D - Ioh/Iol - Type PWR PWR Signal LPC CLK LPC FRAME# LPC RST# LPC AD3 +3V3 LPC AD0 SMB_CLK SB3V3 GND SUS_STAT# PIN 1 3 5 7 9 11 13 15 17 19 2 6 8 10 12 14 16 18 20 Signal GND KEY +5V LPC AD2 LPC AD1 GND SMB_DATA LPC SERIRQ CLKRUN# LPC IRQ# Type Ioh/Iol Pull U/D Note Signal SB3V3 BOOT0 BOOT1 NC GND Type Ioh/Iol Pull U/D Note SPI connector (unsupported).
PAGE 52
986LCD-M Family KTD-N0837-B 4.18 Public User Manual Date: 2012-04-17 Page 52 of 91 Front Panel connector (FRONTPNL).
PAGE 53
986LCD-M Family KTD-N0837-B 4.
PAGE 54
986LCD-M Family KTD-N0837-B 4.20 4.20.1 Public User Manual Date: 2012-04-17 Page 54 of 91 Note PCI Slot PCI Slot Connector Terminal Note Type Signal S C Signal Type PWR O PWR I PWR PWR I I I I OT PWR PWR O PWR O PWR I PWR IOT IOT PWR IOT IOT PWR IOT IOT PWR IOT IOT PWR IOT IOT PWR IOT PWR IOT PWR IOT IOT PWR IOC PWR IOT IOT PWR IOT IOT PWR -12V TCK GND TDO +5V +5V INTB# INTD# REQ2# REQ3# GNT2# GND GND CLKA GND CLKB GND REQ0# +5V (I/O) AD31 AD29 GND AD27 AD25 +3.
PAGE 55
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 55 of 91 Signal Description –PCI Slot Connector SYSTEM PINS Clock provides timing for all transactions on PCI and is an input to every PCI device. All other PCI signals, CLK except RST#, INTA#, INTB#, INTC#, and INTD#, are sampled on the rising edge of CLK and all other timing parameters are defined with respect to this edge. PCI operates at 33 MHz.
PAGE 56
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 56 of 91 ARBITRATION PINS (BUS MASTERS ONLY) Request indicates to the arbiter that this agent desires use of the bus. This is a point to point signal. REQ# Every master has its own REQ# which must be tri-stated while RST# is asserted. Grant indicates to the agent that access to the bus has been granted. This is a point to point signal. Every GNT# master has its own GNT# which must be ignored while RST# is asserted.
PAGE 57
986LCD-M Family KTD-N0837-B 4.20.
PAGE 58
986LCD-M Family KTD-N0837-B 5. Public User Manual Date: 2012-04-17 Page 58 of 91 Onboard Connectors Connector Onboard Connectors Mating Connectors Manufacturer Type no. Manufacturer Type no.
PAGE 59
986LCD-M Family KTD-N0837-B 6. 6.
PAGE 60
986LCD-M Family KTD-N0837-B 6.
PAGE 61
IRQ NMI IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 IRQ16 IRQ17 IRQ18 IRQ19 IRQ20 IRQ21 IRQ22 IRQ23 IRQ24 IRQ25 IRQ26 • • • • • • • • • • • • • • • • • • • • Page • • • Available on PCI slots as IRQA-IRQD depending on BIOS selections May be used by onboard SMBus Controller May be used by onboard VGA Controller Date: 2012-04-17 May be used by onboard Ethernet controller 3 May be used by onboard Ethernet controller 2 May be used by onboard Ethe
PAGE 62
986LCD-M Family KTD-N0837-B 6.
PAGE 63
986LCD-M Family KTD-N0837-B 6.
PAGE 64
986LCD-M Family KTD-N0837-B 7. Public User Manual Date: 2012-04-17 Page 64 of 91 Overview of BIOS features This Manual section details specific BIOS features for the 986LCD-M boards. The 986LCD-M boards are based on the AMI BIOS core version 8.10 with Kontron BIOS extensions. 7.1 System Management BIOS (SMBIOS / DMI) SMBIOS is a Desktop Management Interface (DMI) compliant method for managing computers in a managed network.
PAGE 65
986LCD-M Family KTD-N0837-B 8. Public User Manual Date: 2012-04-17 Page 65 of 91 BIOS Configuration / Setup 8.1 Introduction The BIOS Setup is used to view and configure BIOS settings for the 986LCD-M board. The BIOS Setup is accessed by pressing the DEL key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins.
PAGE 66
986LCD-M Family KTD-N0837-B 8.3 Public User Manual Date: 2012-04-17 Page 66 of 91 Advanced Menu BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Advanced Settings Chipset Exit Configure CPU. Warning: Setting wrong values in below sections may cause system to malfunction.
PAGE 67
986LCD-M Family KTD-N0837-B 8.3.1 Public User Manual Date: 2012-04-17 Page 67 of 91 Advanced settings – CPU Configuration BIOS SETUP UTILITY Advanced Configure advanced CPU settings Module Version –13.04 Manufacturer: Brand String: Frequency : FSB Speed : Cache L1 Cache L2 Intel Intel(R) Core(TM)2 CPU 2.166GHz 667MHz T7400 : 64 KB : 2048 KB Execute Disable Bit Core Multi-Processing Vanderpool Technology Intel(R) SpeedStep(tm) tech.
PAGE 68
986LCD-M Family KTD-N0837-B 8.3.
PAGE 69
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 69 of 91 BIOS SETUP UTILITY Advanced Select the type of devices connected to the system Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. :Hard Disk :ST340014A :40.0GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T.
PAGE 70
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 70 of 91 Feature Hard Disk Write Protect Options IDE Detect Time Out (Sec) 0, 5, 10, 15, 20, 25, 30, 35 Select the time out value when the BIOS is detecting ATA/ATAPI Devices ATA(PI) 80Pin Cable Detection Host & Device Host Device Select the mechanism for detecting 80Pin ATA (PI) Cable Staggered Spin-up delay Disabled Spin-up delay in seconds between each of the SATA drives. Drives must be proper strapped as well. 8.3.
PAGE 71
986LCD-M Family KTD-N0837-B 8.3.4 Public User Manual Date: 2012-04-17 Page 71 of 91 FW/IEEE 1394 Configuration BIOS SETUP UTILITY Advanced Configure the Firewire Device. FW/IEEE 1394 Configuration FW/IEEE 1394 Configuration [Enabled] <|| +F1 F10 ESC Select Screen Select Item change option General Help Save and Exit Exit V02.59+ (C)Copyright 1985-2005, American Megatrends, Inc. Feature Options Description FW/IEEE 1394 Configuration Disabled Enabled Configure the Firewire Device.
PAGE 72
986LCD-M Family KTD-N0837-B 8.3.5 Public User Manual Date: 2012-04-17 Page 72 of 91 Advanced settings – Super IO Configuration BIOS SETUP UTILITY Advanced Allows BIOS to Select Serial Port1 Base Addresses.
PAGE 73
986LCD-M Family KTD-N0837-B 8.3.
PAGE 74
986LCD-M Family KTD-N0837-B 8.3.7 Public User Manual Date: 2012-04-17 Page 74 of 91 Advanced settings – Voltage Monitor BIOS SETUP UTILITY Advanced Enable Hardware Health Monitoring Device. Voltage Monitor Requested Core VcoreA :0.950 V :0.934 V VcoreB +3.3Vin +5Vin +12Vin -12Vin +5VSB :1.467 V :3.387 V :5.067 V :12.074 V :Good :5.094 V <|| +F1 F10 ESC Select Screen Select Item change option General Help Save and Exit Exit V02.59+ (C)Copyright 1985-2005, American Megatrends, Inc. 8.3.
PAGE 75
986LCD-M Family KTD-N0837-B 8.3.9 Public User Manual Date: 2012-04-17 Page 75 of 91 Advanced settings – APM Configuration BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Enable or Disable APM .
PAGE 76
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 76 of 91 Note on “Resume On PME#” (When using PCI LAN WOL function): BIOS version must be 986LCD27 or higher. The LAN card must have a Standby Voltage input to make it possible to implement WOL. Very often such cards have a 3 pin connector and one of the pins is the Standby Voltage. This voltage can be taken directly from the ATX power supply or from the Front Panel connector pin 1 (or pin 2) or from the Feature connector pin 6. 8.
PAGE 77
986LCD-M Family KTD-N0837-B 8.3.11 Public User Manual Date: 2012-04-17 Page 77 of 91 Advanced settings – Remote Access Configuration BIOS SETUP UTILITY Advanced Select Remote Access type.
PAGE 78
986LCD-M Family KTD-N0837-B 8.3.12 Public User Manual Date: 2012-04-17 Page 78 of 91 Advanced settings – USB Configuration BIOS SETUP UTILITY Advanced Enables support for legacy USB. AUTO option disables if no USB Devices are connected. USB Configuration Module Version – 2.24.0-11.4 USB Devices Enabled : 1 Drive Legacy USB Support USB 2.
PAGE 79
986LCD-M Family KTD-N0837-B 8.3.13 Public User Manual Date: 2012-04-17 Page 79 of 91 Advanced settings – USB Mass Storage Device Configuration BIOS SETUP UTILITY Advanced Number of seconds POST waits for the USB mass storage device after start unit command. USB Mass Storage Device Configuration USB Mass Storage Reset Delay Device #1 Emulation Type [20 Sec] JetFlash TS256MJF2L [Auto] <|| +F1 F10 ESC Select Screen Select Item change option General Help Save and Exit Exit V02.
PAGE 80
986LCD-M Family KTD-N0837-B 8.4 Public User Manual Date: 2012-04-17 Page 80 of 91 PCIPnP Menu BIOS SETUP UTILITY PCIPnP Advanced PCI/PnP Settings Warning: Setting wrong values in below sections May cause system to malfunction. Plug & Play O/S Allocate IRQ to PCI VGA PCI Slot-1 IRQ Preference [No] [Yes] [Auto] NO: lets the BIOS configure all the devices in the system.
PAGE 81
986LCD-M Family KTD-N0837-B 8.5 Public User Manual Date: 2012-04-17 Page 81 of 91 Boot Menu BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Configure Settings during System Boot. Boot Settings > Boot Settings Configuration > Boot Device Priority <|| Enter F1 F10 ESC Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit V02.59+ (C)Copyright 1985-2005, American Megatrends, Inc. 8.5.
PAGE 82
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 82 of 91 Feature Options Description Quick Boot Enabled Disabled Allows BIOS to skip certain test while booting in order to decrease boot time. Quiet Boot Disabled Enabled Black Screen White Screen Disabled: Displays normal POST messages. Enabled: Displays OEM Logo. Black Screen: Displays black picture (noting). White Screen: Display white picture. Disabled WinXP ™ Vista ™ (Long Splash only available if Quiet Boot).
PAGE 83
986LCD-M Family KTD-N0837-B 8.5.2 Public User Manual Date: 2012-04-17 Page 83 of 91 Boot – Boot Device Priority BIOS SETUP UTILITY Boot Specifies the boot sequence from the available devices. Boot Device Priority 1st Boot Device [ESS-ST380811AS] A device enclosed in paranthesis has been disabled in the corresponding type menu. <|| Enter F1 F10 ESC Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit V02.59+ (C)Copyright 1985-2005, American Megatrends, Inc.
PAGE 84
986LCD-M Family KTD-N0837-B 8.6 Public User Manual Date: 2012-04-17 Page 84 of 91 Security Menu BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Install or Change the password.
PAGE 85
986LCD-M Family KTD-N0837-B Public User Manual Date: 2012-04-17 Page 85 of 91 Supervisor Password protection (setup Supervisor before User) Supervisor PSW BIOS User Access control Full CMOS (most) Date&Time * Supervisor PSW View User PSW Limit None * = also: Quick Boot Quiet Boot Repost Video on S3 Resume Active State Power-Management Remote Access.
PAGE 86
986LCD-M Family KTD-N0837-B 8.7 Public User Manual Date: 2012-04-17 Page 86 of 91 Chipset Menu BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Configures North Bridge features. Advanced Chipset Settings Warning: Setting wrong values in below sections may cause system to malfunction. > North Bridge Configuration > South Bridge Configuration <|| Enter F1 F10 ESC Select Screen Select Item Go to Sub Screen General Help Save and Exit Exit V02.
PAGE 87
986LCD-M Family KTD-N0837-B 8.7.2 Public User Manual Date: 2012-04-17 Page 87 of 91 Advanced Chipset Settings – Video Function Configuration BIOS SETUP UTILITY Chipset Video Function Configuration DVMT Mode Select DVMT/ Fixed Memory [DVMT Mode] [128MB] Boot Type: Backlight Signal Inversion LCDVCC Voltage [CRT] [Disabled] [3.
PAGE 88
986LCD-M Family KTD-N0837-B 8.7.3 Public User Manual Date: 2012-04-17 Page 88 of 91 Advanced Chipset Settings – SouthBridge Configuration BIOS SETUP UTILITY Chipset South Bridge Chipset Configuration USB Functions USB 2.
PAGE 89
986LCD-M Family KTD-N0837-B 8.8 Public User Manual Date: 2012-04-17 Page 89 of 91 Exit Menu BIOS SETUP UTILITY Main Advanced PCIPnP Boot Security Chipset Exit Exit system setup after saving the changes. Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes F10 Key can be used for this operation.
PAGE 90
986LCD-M Family KTD-N0837-B 8.9 Public User Manual Date: 2012-04-17 Page 90 of 91 AMI BIOS Beep Codes Boot Block Beep Codes: Beeps Description 1 Insert diskette in floppy drive A: 2 ‘AMIBOOT.
PAGE 91
986LCD-M Family KTD-N0837-B 9. Public User Manual Date: 2012-04-17 Page 91 of 91 OS setup Use the Setup.exe files for all relevant drivers. The drivers can be found on the 986LCD-M Driver CD or they can be downloaded from the homepage www.kontron.com Note: When installing/using ADD cards like ADD-DVI or ADD-LVDS it's possible that the OS start up without any connected display(s) active. If you are able to pass the "Log On to Windows" etc. by entering the password etc.