User Manual

KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
26772-000-56/87 Rev.5c 03-80-852-00 2/21
TECHNICAL DATA
Material
Foot plate, Tray plate: Steel,
powder coating, black, gray
Load max. 15 kg central load
Dimensions
Base: W x D 214 x 210 mm
Bearing plate: W x D 150 x 170 mm
Height: 167 - 254 mm
Packaging Box: 270 x 270 x 190 mm
Weight 3.1 kg
26772 Table monitor stand
Attractive table stand for studio monitors and loudspeakers
- Variable height adjustment between 167 and 254 mm
- Adjustable by hand without the use of tools
- Anti-slip stand and de-coupled thanks to the
- four rubber knobs for the surface and tray.
- Recommended max. weight up to 15 kg
- Tray W x D 150 x 170 mm
SAFETY NOTES
Thank you for choosing this product. Please read and follow these instructions
carefully. They inform you about all necessary and important steps concerning safe
installation and operation. We recommend that you keep them for future reference.
- Maximum centered load: 15 kg
- The surface must be load bearing and even.
- Center the monitor (check placement regularly)
- Any adjustments to the stand (position, height)
- must be done without the monitor on the stand
- The fact that the product is adjustable, can result in the risk of
- pinching/wedging: careful handling is therefore essential
SETUP INSTRUCTIONS
1. COMPONENTS
a. STAND: a.1 Footplate - a.2 Clamping elements - a.3 Tray
b. RUBBERIZED KNOBS:
b.1 Strip with 4 self-adhesive rubber knobs ø 20 mm for the foot plate
b.2 Strip with 4 self-adhesive rubber knobs ø 13 mm for the tray
2. MOUNTING
The product comes completely pre-assembled.
2.1 Only the 4 rubber knobs ø 13 b.2 for the monitor and the
2.1 4 rubber knobsø 20 b.1 for the floor have to be glued on
2.1 - depending on the dimensionsof the monitor/floor and
2.1 as far apart as possible.
USAGE NOTES / FUNCTION
3. HEIGHT ADJUSTMENT
If needed, remove the monitor from the tray
3.1 Hold the tray and...
3.2 ...loosen the clamping nut some.
3.3 Adjust to the desired height and...
3.4 ...tighten the clamping nut.
4. CLAMPING
The clamping nut is pre-mounted and points forward.
For optical and practical reasons this can also be
placed on the back of the stand.
If needed, remove the monitor from the tray
4.1 Hold the tray
4.2 Unscrew the clamping bolts from each other completely.
4.3 turn the clamping element 180°...
4.4 ...and tighten them again;
4.5 In this process be sure that the foot plate pegs are
4.5 placed into the slits of the tray plate.
5. DIMENSIONS
FAULT-FINDING (F) and REPAIR (R)
INSPECTION and MAINTENANCE
F: Installation is not stable
F: B: Check surface, check rubber knobs, tighten clamps
F: Tray is leaning forward
F: B: Plate is bent,
F: B: pegs are not properly placed in the slits of the desk plate 4.5
- During maintenance work - always in unloaded state- always pay
- attention to possible hazards (jamming, bumping, tilting)
- To care for the product, use a damp cloth and a non-abrasive
- cleaning agent.
1. COMPONENTS
2. MOUNTING
3. HEIGHT ADJUSTMENT
4. CLAMPING 5. DIMENSIONS