User Manual

KÖNIG & MEYER GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
19798-300-55 Rev.04 03-80-089-00 1/18
TECHNICAL DATA
Material
Tubes, screws: Steel, black powder coating, galvanized
Clamping brackets: Zinc, black powder coating
Base, joints, clamps, handles, Holder: PA-6
End caps: TPE
max. load
Tablets Height: min. 163 mm, max. 242 mm
Tablets Width: min.102 mm, max. 189 mm
Tablets Depth: min. 5 mm, max. 11 mm
Dimensions
External Dimensions W x D x H: 171/250 x 100 x 123/210 mm
Stand: ø 565 mm x 700/1550 mm
Packaging W x D x H: 588 x 185 x 112 mm
Weight net 1.8 kg, gross 2.4 kg
SETUP
FAULT-FINDING (F) and REPAIR (R)
F: Holder is unstable
F: R: Check that it is properly screwed into the stand, if needed tighten
F: R: the screws 2.
F: Tablet is not securely in place
F: R: Correct the position of the side support arms, so that the corner
F: R: supports are properly set on the Tablet without any play 3-10
F: R: Ensure that the lower support arms setting are symmetrical 5,6.
F: R: Asymmetric setting of the support arms looks bad and does not
F: R: ensure that the Tablet is securely held in place.
F: B: Do not only place the Tablet on the upper support arm, but be sure
F: R: it clicks into place 8,9.
F: B: Observe the minimum i.e maximum dimensions 21
USAGE NOTES and FUNCTIONS
The angle and format of the
tablet can be adjusted.
The (securely positioned) Tablet
does not have to be removed
from the holder.
ANGLE (17-19)
The Tablet can be adjusted to
any final position by adjusting it
vertically and horizontally. To do this:
16 Hold the Tablet and loosen the wing
16 nut somewhat
17 Pick the position (vertical/horizontal) and...
18 ...re-tighten the wing nut.
FORMAT (20)
The holder has a
90°-Twist Function.
The Tablet can be presented
in landscape and portrait positions.
20 Take the holder and turn it to
20 the landscape, portrait or tilted
20 - position!
20 NOTE- Hitches within the mount limit
20 how far the holder can be turned.
DIMENSIONS (21)
The minimum and maximum size cannot
be achieved due to the Tablet’s
unfavorable length/width ratios.
ANGLE (17-19)
FORMAT (20) DIMENSIONS (21)
REMOVING the Tablet (11-13)
REPEATED PLACEMENT of the Tablet (14-16)
Final Position
- horizontal
- as far as
- it goes
Final Position
- vertical
- as far as
- it goes
Interim Position:
- tilted (0-90°)
- select any position (Secure position
- by tightening the wing nut 17
Final Position
-landscape
- clicked into place
Final Position
portrait
- clicked into
- place
Twist (Interim Position):
- tilted
- not clicked into place, however it
- does stay in the selected position
REMOVING the Tablet (11-13)
11 Loosen the three knurled pins a bit
12 Hold the tablet and LIFT UP the catch
13 Flip out the Tablet and REMOVE
If you always use the same tablet, we
recommend that the support arm settings
remain in this position.
Or remember or mark at least the
scale values.
REPEATED PLACEMENT of the Tablet (14-16)
For previously set support arms
14 Place the tablet in the lower corner
14 supports
15 Place the tablet into the upper catch and
15 gently press until it clicks into place
16 Tighten the knurled pins until the tablet
16 is gently pressed into place
Then check that the Tablet is secure as
described in 10.