Installation Manual

5.1
Place L-base tubes in the corresponding recesses
of the support tubes and screw them together using
the two lock screws h and flange hexagon nuts f.
Use key SW10 i.
Please read the following pages concerning SAFETY INSTRUCTIONS, particularly
Chapter B. DANGER OF TIPPING - REASONABLY FORSEEABLE MISUSE
For the installation we recommend the following procedure:
6.1 Ensure the correct position of the rubber feet on attachment 18811 (see 5.2)
6.2 Assemble attachment pair 18822 according to instructions for use
6.3 SEQUENCE when loading: 1
st
the lower level, 2
nd
the middle level,
6.3 finally 3rd topmost level.
6.4 Check tipping tendency of the installation whilst keeping safety in mind
6.5 SEQUENCE during UNLOADING: 3
rd
top level first, 2
nd
middle level finally,
6.5 1st bottom level last.
The distance of the 2nd and 3rd level naturally corresponds to the
undermost level. If the equipment in use requires different distances,
we recommend using trays from our product range.
7.1 The base support must first be set to a width of 610 mm
7.1 (see chapter 3.2, item 3).
7.2 Plate 18819* for attachment 18811 (see 2. = middle level)
7.3 Plate 18824* for attachment 18822 (see 3. = top level)
* Please observe the respective instructions applying to the plates.
5.2
The floor rubber feet j are glued to the respective pipe
ends at a distance of 10 mm.
NOTE: Please do not exceed the distance of 10 mm
(in particular at the rear) since a larger distance can
be at disadvantage to tilt safety (see SAFETY
INSTRUCTIONS - B. DANGER OF TIPPING).
5.3
The hemispherical keyboard rubber pads k are also self-
adhesive and attached to the top of the pipes. The exact
position depends on the shape and size of the keyboard.
5. ASSEMBLY OF
5. ATTACHMENT 18811
6. ASSEMBLY OF THE ATTACHMENT 18822 (3
rd
level) 7. TRAYS 11819 & 18824
FAULT-FINDING (F) and REPAIR (R)
F: Base support 18828 wobbles
F: B: Check if the screws are firmly tightened
F: B: Make sure that the heads of the hexagon bolt d are seated in the corresponding
F: B: recesses of the support tubes
F: Keyboard sits crooked or wobbles
F: B: Make sure that the keyboard rubber feet (k) protrude beyond the flange hex nut f
F: B: The following applies to both attachments (18811, 18822):
F: B: - adjust the front stopper of the attachments synchronously
F: B: - ensure that the right and left support have the same height
F: B: - always set the same inclination angle
F: B: - Place rubber pads so that keyboards rest on them
F: Connection between base support 18828 and attachment wobbles
F: B: Check if screw connections f, h are correctly seated and firmly tightened
F: The installation (especially when loaded) tends to tilt backwards
F: B: Make sure that the rubber feet are correctly seated (see 5.2)
F: B: Reduce or completely remove the 3
rd
level weight
F: B: Move load balance point forward, e.g. by changing the support depth (see annex to the attachments)
TECHNICAL DATA
Material
Tubes: Steel, powder-coated, black
Screw connections: Steel, galvanised
Plastic parts: PE, TPE, black
Load Stackers 18811: max. 25 kg, 18822: max. 8 kg
Dimensions
Tubes: Supports 40 x 20 mm,
Connection 35 x 15 mm
Length of tube combination: min. 587 - max. 831 mm
Width distance of the attachments:
1 = 488 / 2 = 549 / 3 = 610 / 3 = 671 / 5 = 732 mm
Packaging Cardboard: Inside: 710 x 47 x 47 mm, 0.13 kg
Weight 1.3 kg
Attachments
(optional)
Stacker 18811 - Controller keyboard tray 18819
Stacker 18822 - Controller keyboard tray 18824