Operation Manual

3
4) Placethecuponaattabletodisplaythereading.Oncethereadingisshown,youmayalsoholdthecup
in your hand for easy reading
NOTE:Thevolumemeasurementisconvertedfromtheweightandthepre-setdensityoftheingredientby
theprocessorinthecup.Therearedifferenttypesofmilk,oil,sugarorouronthemarket.Differenttypes,
brands & origins of the same ingredient have different density. For this reason, some variation of the volume
measurement will occur depending on the type of ingredients you are using. The volume reading provided by
the cup can only be used as an approximate value.
The density and type of ingredients being used in the cup are shown below.
Density units selection available
Water 1kg/l ML,CUPS,FLOZ
Milk 1.03kg/l ML,CUPS,FLOZ
Oil 0.9kg/l ML,CUPS,FLOZ
Sugar(granulatedsugar) 0.84kg/l GRAMS,CUPS,LBSOZ
Flour(allpurposeour–notsifted) 0.6kg/l GRAMS,CUPS,LBSOZ
Thedisplayresolutionof“FLOZ”and“CUPS”is1/8.Ifnerresolutionandhigheraccuracyisrequired,please
selectmL(orgram)forthemeasurementandconvertbacktoFLOZorCUPSifneeded.
Tare(setzero)Function
Itiseasyandconvenienttobuildupandmixdifferentingredientstogetherallinthesamecup.Aftertherst
ingredient is added and measured, you may add another ingredient after performing the tare function as
described below.
- Placethecupwithrstingredientonaattable
- Pressthe[0]buttononce.Thereadingwillresettozeroandthe“TARE”iconwillremainontheupper
display
Nowyoucanaddyouradditionalingredient.Onlytheweightorvolumeofthelastingredientaddedis
measured. Continue the above procedure to build up different ingredients for your recipe.
NOTE:Thetarefunctiononlyfunctionscorrectlyifthecupisplacedonaatsurface
Reversing the Tare Function
Rightafterthetarefunctionhasbeenperformedandthedisplayisshowing“0”withthe“TARE”icondisplayed,
youcanpressthe[0]buttontoresumetotheoriginalweightorvolumereadingjustasbeforethetarefunction
andthe“TARE”iconwilldisappear.
NOTE:Thereversetareonlyfunctionsifthecupisplacedonaatsurface
MIXING(IMPORTANTNOTE)
Itiseasyandconvenienttomixdifferentingredientsinthebowlscale.Itcanwithstandupto5Kgofmaximum
loading.Whenthetotalweightandforceduringmixingisgreaterthan5kg,theunitwillbeepanddisplay“Err”.
Make sure to remove the weight and stop the mixing action immediately.
Sensitive weight scale components are located at the base of the scale and excessive force & weight applied
to the base may permanently damage the scale inside and provide inaccurate reading.
To extend product life span, please detach the bowl and mix your ingredients on the detached bowl when the
loadingisclosetoorgreaterthan5kg.
FAULT MESSAGE DISPLAY
UnSt:Unstable
Thescaleisunstableandtheunitwillturnoffautomatically.Placethecuponaattableandturnontheunit
againbypressingthe[0]buttononce.
Err:Error
Thescaleisoverloaded.Theweightorvolumeinthebowlexceedsthemaximumdisplayrange(refer
“Specication”section)andtheunitwillbeeps.Removetheweight&stopallmixingimmediately.
CALIBRATION
To ensure an accurate measurement, it is recommended to check the weight of an empty cup every time you
turnontheunit.Itshouldread0gram(oroz)foryouremptycup.