KIP 720 User Manual Ver. A.
Thank you for purchasing KIP 720. This USER'S GUIDE contains functional and operational explanations for KIP 720. Please read this USER'S GUIDE carefully before using KIP 720. Please keep this USER'S GUIDE for future reference. Installed in USA This device complies with part 15 of the FCC Rules.
Safety Warnings The following warnings are very important in order to safely use this machine. These notes are important in preventing danger to the operator or operation of the product. The following symbols are found throughout the document and have the following meaning: WARNING This WARNING mark means that th ere is a po ssibility of death or serious injury if you ignore or do not follow the said instruction.
WARNING Ground the machine with a correct ground source or you may be electrically shocked. 1. The power source should be as follows: 100 - 240VAC, 50/60Hz, 0.5A or higher 2. Use a circuit with a dedicated breaker. 3. Install the machine as close to the wall outlet as possible. 4. If you want to move the machine, contact your service personnel. 1. Do not remove the screw and do not open the cover if not said to do so in this User’s Manual.
CAUTION Do not install the machine in a humidified room or a dusty room. Also, do not install the machine on an unstable floor as injuries may occur. Be careful not to catch a finger in the Top Cover. 1. Unplug the machine before you move it. The power cord may damage and it may result in a fire or an electrical shock. 2. If you do not use the machine for a long duration (holidays, company shutdown) turn off and unplug the printer from the outlet for safety.
POWER CORD INSTRUCTION The Power Cord is necessary for with rating 125VAC or 250VAC more than 3A and use the thing which was equal to the standard of the specifications country. The installation of (or exchange to) a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the following: WARNING Select a power plug which meets the following criteria; - The plug has a voltage and current rating appropriate for the product’s rating marked on its name plate.
Chapter 1 Before Use 1. 1 Installation Requirements page 1- 2 1. 2 Originals Prohibited from Duplication 1- 3 1. 3 Features 1- 4 1. 4 Specifications 1- 5 1. 5 Appearance 1- 7 1.
1. 1 Installation Requirements The following conditions have to be satisfied when installing KIP 720 Scanner. 1. Satisfy the following input power condition. Voltage Current Frequency 100 - 240VAC 0.5A or higher 50 / 60Hz. KIP 720 can be supplied with any voltage within 100 to 240VAC. If the voltage is within this range, please connect to the outlet simply. (No setting has to be changed.) 2. Make sure to connect the power plug to the outlet that is provided with the Ground Terminal. 3.
1. 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original. You may be punished by the law if only you possess the copy of some kind of original. We recommend you to consider enough before you copy such original. [Originals prohibited from copying by the law] 1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.); Government issued Negotiable Instruments (National Bonds, Security, Local Debt Bonds, etc.). 2.
1. 3 Features The KIP 720 has the following features. Wide format image scanner KIP 720 is available for various sized originals. 210 - 914.4 mm (8.5 - 36”) in width 210mm (8.5”) - 6,000mm in length. High speed scanning KIP 720 provides quick scan operation (65mm/s in monochrome / grayscale, 22mm/s in color on 600 dpi). High resolution scanner head KIP 720’s 600dpi CIS enables clear and high quality color / monochrome images.
1. 4 Specifications Model Scanning method Reading sensor Light source Setting Starting point of scan Original size Scanning Width Scanning Length Start point of reading Color mode Scanning speed (600 dpi) Resolution Interface Input power KIP 720 Sheet through type Contact Image Sensor (for A4 size x 5 pieces in staggered arrangement) LED (R/G/B) Face up Center Max. : 970.0mm Min. : 150.0mm Thickness : 0.05mm to 1.60mm (Image quality for an original with 0.
1. 5 Appearance 3 2 1 7 6 4 8 4 5 No. 1 Part Name Upper Unit 2 3 4 5 6 Original Tray Original Table Original Guide Main Power Switch Start Button 7 Stop Button 8 LED Indicator Function Reads original images. To be opened for cleaning / removing original jam. Receives an ejected original. Used to place an original. Guides an original to the scanner straight. Turns on / off KIP 720. Starts scanning if the controlling software requires user intervention.
9 No. 9 Part Name USB Terminal 10 AC Inlet 10 Function Connect a USB cable from the controller PC or a KIP Printer. (Maximum: 5VDC) Connect a power cord.
1. 6 Specifications for Scan Originals Scan originals must satisfy the following specifications. Thickness 0.05-1.60mm Width 210-970mm (the maximum scanning width is 914mm (36”)) 210mm-25,000mm (If an original is longer than 6,000mm, its image quality and the original feeding are not guaranteed.) Length Do not scan the following kinds of originals. The original or the scanner may damage. However, with a carrier sheet, it is possible to scan some of the following original.
Pasted With a carrier sheet, it is possible to scan. Paste Patched With a carrier sheet, it is possible to scan. Torn With a carrier sheet, it is possible to scan. Folded (especially at leading edge) With a carrier sheet, it is possible to scan. Not square With a carrier sheet, it is possible to scan. KIP KIP Excessively curled (a diameter of 80 mm or less) With a carrier sheet, it is possible to scan.
Rough surface (Carbon paper for example) Rough surface Punched With a carrier sheet, it is possible to scan. With a carrier sheet, it is possible to scan. Extremely creased Extremely thin and soft With a carrier sheet, it is possible to scan. Transparent With a carrier sheet, it is possible to scan.
Chapter 2 Hardware Operation 2. 1 Turning on KIP 720 page 2- 2 2. 2 Turning off KIP 720 2- 3 2. 3 USB Connection 2- 4 2. 4 Installing USB Driver Software to your PC 2- 5 2. 5 Scanning Original 2- 8 2. 6 Canceling Scan 2-12 2. 7 Auto Power OFF 2-13 2.
2. 1 Turning on KIP 720 1. Plug the power cord to a dedicated outlet. WARNING (1) Do not handle the power plug with a wet hand. It may result in receiving an electrical shock. (2) Be sure to ground the machine. (3) Use a dedicated outlet for KIP 720. Many loads on a single outlet may cause overheating and result in a fire. (4) The outlet must satisfy the following conditions; 100-240VAC, 50/60Hz, 0.5A or higher 2. Press “I” side of the Power Switch on the right side. Press “｜” side. 3.
2. 2 Turning off KIP 720 1. Press “ ” side of the Power Switch on the right side. Press “ ” side. NOTE Wait at least 5 seconds for turning on the scanner again.
2. 3 USB Connection The KIP 720 should be connected with a supported KIP printer or a PC through a USB cable for any operation. NOTE You can purchase another USB Cable separately. Make sure that the cable satisfies the following specifications. - USB 2.0 - High-speed data transfer - Shielded - Shorter than 3 meters Printer / PC: Type A male Scanner: Type B male 1. Connect the Type B connector to the USB port on the scanner’s rear side. USB port USB cable 2.
2. 4 Installing USB Driver Software to your PC When the KIP 720 is connected to a PC, the PC should have the driver software installed. NOTE (1) When the KIP 720 is connected to a supported KIP printer, the installation of the driver software is not required. Turn on the printer, connect the USB cable and then turn on the scanner. (2) The driver software supports Windows 2000 and both 64/32 bit editions of Windows 7, Vista, XP.
5. Choose “Install the software automatically (Recommended)” and press [Next]. If the driver software is not detected automatically, select “Install from a list or specific location (Advanced)”, and locate either of “stiK129x64.inf” or “stiK129x86.inf”. Folder “x64” Folder “x86” stiK129x64.inf stiK129x86.inf for 64 bit edition OS for 32 bit edition OS 6. If the notification for Windows Logo testing appears, press [Continue Anyway]. 7. When the installation is completed, press[Finish].
8. Open “Device Manager” (Control Panel Æ System, for example) and confirm that “K129” has been added under Imaging devices.
2. 5 Scanning Original 1. Slide Original Guides to align them to the original’s width. Original Guide 2. Place an original on Original Table in face-up. Insert the leading edge to the scanner along with Original Guides. NOTE (1) Align an original to Original Guides to avoid skewing. (2) Position an original in the center of Original Table. Not doing so may result in skewing. (3) Do not place any objects except originals on Original Table. The scanner may catch such objects and result in damage.
3. When the original is at wait position, the LED Indicator will turn off. The KIP 720 starts scanning. Pressing START button may be required to start the scan according to the scanner’s controller software. For further details of “Auto Start”, see the software’s document. START button Reference Use a carrier sheet for the following kinds of originals. (We will not guarantee the image quality or reliability of original feeding when the carrier sheet is used.) NOTE Handle a carrier sheet carefully.
Reference Patched Torn Folded (especially at leading edge) Not square KIP KIP Extremely curled (Less than 80mm in diameter) (Continued) 2-10 Chapter 2 Hardware Operation
Reference Rough surface Creased Extremely thin and soft Transparent 2-11 Chapter 2 Hardware Operation
2. 6 Canceling Scan 1. Press STOP button during the scan. The LED Indicator flashes red and the original stops. LED: flashes RED STOP button 2. When the original stops, lift up both sides of the Upper Unit, and remove the original by hand. See [3.1 Original Misfeed]. Lift up here. from the rear Lift up here. 3. Gently press down both sides of the Upper Unit until it locks. Press down here. Press down here. 4. The LED Indicator will turn green “Ready”.
2. 7 Auto Power OFF The KIP 720 has Auto Power OFF feature for energy saving purpose. After a certain period of inactivity passes, the Power Switch will turn off. The period can be configured (0-60 minutes). After Auto Power OFF function ran, please press “ | ” side of the Power Switch to turn on the scanner again. NOTE (1) In combination use with a supported KIP Printer, Auto Power OFF runs after the KIP printer goes Cold Sleep. It does not while the KIP printer is in ready (standby).
2. 8 Removing Original Tray NOTE When scanning originals as follows, removing Original Tray is recommended. Original Trays may damage such object. - Original in a carrier sheet - Tough original (cannot be transported along with Original Tray) Remove Original Trays from the scanner’s rear. Original Guides To reinstall Original Trays, attach its notches on the rear.
Chapter 3 Troubleshooting 3. 1 Original Misfeed page 3- 2 3. 2 Error Indication 3- 4 3. 3 Original Not Carried 3- 4 3.
3. 1 Original Misfeed The scanner may stop feeding the original in the scanner if the original skews. Pressing STOP button during scanning also stops the original in the scanner. There is no eject/rewind feature for a stopped original. Remove the original by hand. NOTE (1) Open/close the Upper Unit with holding both sides of the Upper Unit. (2) Be careful not to catch your finger in the Upper Unit. 1. Lift up both sides of the Upper Unit. Upper Unit Lift up here. Lift up here. 2.
3. Gently press down both sides of the Upper Unit until it locks. Press down here. Press down here.
3. 2 Error Indication In case of a misfeed, emergency stop, the Upper Unit open the LED Indicator turns red “Error”. flashes: - Upper Unit open (half-shut), - Misfeed, - Emergency Stop solid: - Document remaining in the scanner at the time of power on, - the other internal errors Check the followings to clear the error. 1. Remove an original in the scanner. See [3.1 Original Misfeed]. 2. Clean the sensors on the Upper Unit to remove dust or a paper portion. See [4.1.2 Sensors]. 3.
3. 3 Original Not Carried If the KIP 720 does not start carrying an original, check the followings. 1. Clean the sensors on the Upper Unit to remove dust or a paper portion. See [4.1.2 Sensors]. 2. Check the USB connection. 3. Replace the USB cable. 4. Check the configurations on the scanner’s controller software. See your system’s document. 3. 4 Other Errors Your monitor device (of your KIP printer’s touchscreen / PC) may display a kind of information as follows.
Chapter 4 Maintenance 4. 1 Cleaning 4. 1. 1 Scan Glass, Feed Roller, Guide Plate 4. 1.
4. 1 Cleaning 4. 1. 1 Scan Glass, Feed Roller and Guide Plate If Scan Glasses, Feed Rollers or Guide Plates get dusty, it may result in a poor scan image. Perform cleaning as needed. NOTE (1) Open/close the Upper Unit with holding both sides of the Upper Unit. (2) Be careful not to catch your finger in the Upper Unit. (3) Never use organic solvent, glass cleaner or antistatic spray for cleaning. (4) For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1.
3. Gently wipe the Scan Glass and Feed Rollers (white) with a soft cloth. Equal mixture of water and neutral detergent can be used. Scan Glass Feed Rollers (white) NOTE Do not use organic solvent, glass cleaner or antistatic spray for cleaning. 4. Wipe the Feed Rollers (rubber) with a dry cloth.
5. Wipe dry the Feeding Rollers. 6. Wipe the Upper Guide Plate and the Lower Guide Plate with a dry cloth. Guide Plate Guide Plate 7. Gently press down both sides of the Upper Unit until it locks. Press down here. Press down here.
4. 1. 2 Sensor If Sensors are dirty, the original may be detected incorrectly. Perform cleaning or as needed. NOTE (1) Open/close the Upper Unit with holding both sides of the Upper Unit. (2) Be careful not to catch your finger in the Upper Unit. (3) Never use water, organic solvent, glass cleaner or antistatic spray for cleaning. (4) For ease of visual check, this document shows the Upper Unit fully open (not actual wide). 1. Press “ ” side of the Power Switch on the right side. Press “ ” side. 2.
3. Gently wipe Sensors (4) with a dry cotton bud. NOTE Do not use water, organic solvent, glass cleaner or antistatic spray for cleaning. 4. Gently press down both sides of the Upper Unit until it locks. Press down here. Press down here.
Wide Format Color Document Scanner KIP 720 Hardware Operation Guide Version A.1 (Issued on April 12, 2012) Published by Katsuragawa Electric Co., Ltd. 21-1 Shimomaruko 4-Chome, Ohta-ku, Tokyo 146-8585, Japan Please note that some articles, illustrations and photographs might be partially different from the actual machine because of the modification of machine and so on. © 2012 Katsuragawa Electric Co., Ltd.
